Find a Builder you can trust in Castlewellan.

Have you been advised by a structural engineer or a surveyor that your building needs to be underpinned? Well, this might just have you wondering what underpinning really is and how long it lasts. In this post, we’re going to tell you more about underpinning to help you make the best-informed decision possible moving forward. Let’s take a look!

Basically, underpinning refers to the incorporation of one of various methods to reinforce or repair the old foundations of a building or structure mostly to remedy or avoid subsidence. Now, subsidence can be caused as a result of poor soil quality, increase in the load on the foundation like adding a new storey, excavations below the building as well as inadequate foundation which is more common in older buildings. When an underpinning remedial work is carried out, there are a plethora of benefits that comes with it. It’s preserves the structural integrity of your building by strengthening it, make it a lot more attractive, increases the property’s value and makes it a lot safer for both you and your loved ones. So how long does underpinning last?

Well, many underpinning contractors will offer you a 10-year guarantee of its underpinning solutions for defects. Primarily, there are two reasons why underpinning can fail which is poor installation and fresh issues arising or unforeseen circumstances. While the first is an issue that can be avoided by employing the services of an expert contractor who possesses vast experience and knowledge in the field, the second can not be avoided. However, in the absence of the unforeseen issues, underpinning is expected to last for the natural life of the building, so far it has been expertly installed.

How Much Do Roof Rooms Cost?

The price of your roof room may vary depending on your location within the country. Other factors that can also play a key role in determining the price of a roof room includes the conversion’s type as well as the legal and technical issues it’s currently facing. Usually, the cost of roof rooms will range between £1,200 to £2,000 per square metre. The differences in the price per square metre is influenced by the size of the alterations to the roof, the type of roof room to be constructed, the access, location as well as the finishing type.

• DORMER LOFT CONVERSION.

Here, one of the slopes of a pitched roof is substituted for a box-shaped structure. The outcome is a flat roof space which enables the fitting of full sized windows as well as the incorporation of several appliances. This is quite expensive as it involves a total rebuilding of one roof pitch alongside the complete internal works that are associated. The average cost of a standard dormer loft project will range between £25,000 to £50,000.

• HIP TO GABLE LOFT CONVERSION

Here a vertical brick wall is used to substitute the roof’s slope at the ending part of the terrace on detached buildings. The average cost of this type of roof room will range between £32,000 to £60,000.

• ROOFLIGHT LOFT CONVERSION

This basically involves fitting rooflight windows in the roof. Other improvements include flooring, plasterboarding, strengthening of the existing floor, as well as installation of rooflights. The average cost of this type of roof room will range between £15,000 to £25,000.

• MANSARD LOFT EXTENSION

This roof room can create an extra storey on top of an existing building as it makes a space featuring two or four external walls that are a bit sloped. The average cost of this type of roof room will range between £40,000 to £70,000.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.

If you’re considering rendering your house or property, then you’d most likely want to know whether or not applying for a planning permission will be needed. In several cases, planning permission will not be required for the maintenance, repair as well as replacement of the existing render on your building. These activities are covered by what’s called “Permitted Development Rights, which allows you to carry out some activities without having to apply for a planning permission but always subject to following some strict guidelines. For rendering, as long as the material (render) possesses an identical appearance to those existing on the house as well as same colour, then you will not require a planning permission. However, there are a number of projects that have been highlighted in which a planning permission would be required. These includes the following:

✓ Re-rendering in a colour that different from the original one used on the house or building.

✓ Rendering over brickwork which was not originally covered.

✓ Rendering over pebbledash

✓ Removing pebbledash and replacing it with render.

Another exception to the Permitted Development rights are for houses in conservation areas, national parks or areas of outstanding national beauty.

Although, you wouldn’t normally require to submit a planning application for approval before you apply render, but in truth it’s actually a bit of a grey area which isn’t totally clear and doesn’t allow for much freedom or creativity. And due to this fact, homeowners who wants an absolute peace of mind may opt to apply for planning permission just in case. It’s also worth noting that whether or not a planning permission is required, a huge rendering work will need to comply with building regulations which includes the need to insulate walls on the inside or outside as part of the work on several older properties .

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

The short and simple answer to this question is yes, you can build a room in your garden. In fact, if you want an additional space for a living room, dining room, games room, study room or perhaps you want something as cool as a pool house, then looking at your garden for a solution may just be the perfect answer to your need for an extra outdoor living space.

Outbuildings such as garden rooms do not usually require planning permission as they’re usually covered by the permitted development. As a result, making it even a lot more attractive to homeowners who would not like to pass through the stress involved or pay the money required to submit an application for planning permission. However, if you need your garden room to be covered by permitted development ( if it’s not a listed building or in a designated area), you must follow these guidelines:

✓ The garden room shouldn’t be in front of your home or property.

✓ The total area of your extensions, sheds and outbuildings ( which includes your garden room), must not go beyond 50 percent of the total land area surrounding your property.

✓ It must be a single storey that’s less than 3 metres high ( 4 metres for a dual pitched roof). And it must not go beyond 2.5 metres in height if the structure is within 2 metres of your boundary.

✓ The eaves must not go beyond 2.5 metres above ground level.

✓ It must not feature a balcony, veranda or any raised platform

✓ It must not be a self contained living accommodation.

The position of your garden room will be partly determined by the space available in your garden. If you need it to link it to your utilities then positioning it a bit close to your main house would be a cost effective choice unless you’re using off grid sources of power, heat as well as water.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the Federation of Master Builders. They have a search tool where you can find precise crafts in your area and look at their situations. All FMB members are assessed and individualistically examined and are checked to ensure that they have the correct insurances in place.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.