Find a Builder you can trust in Wadebridge.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

If you’re planning to construct a kitchen extension on your property, one of the first things that comes to mind is whether or not you’ll require a planning permission before you proceed. Generally, kitchen extensions are normally classified as permitted development which allows you to carry out your project without any interruptions from the law or your local authority. In other words, if your extension is meets up with the guidelines of the permitted development rights, you won’t have to apply for a planning permission. However if otherwise, you’ll have to apply for a planning permission to your local council and may require additional reports. And regardless of your position, you’ll always need building regulations approval before you can carry out any kitchen extension project. It may also be required that you’ll have to issue a part wall notice if you’re to build on or close to the boundary with a neighbour.

If you don’t want to go through the hassle and stress involved in applying for a planning permission with your local council, then you must ensure the following:

✓ Your kitchen extension must not be over half of the area of land around your main house.

✓ The kitchen extension must not be side elevation onto a highway or forward of the principal elevation.

✓ The extension must not be taller than the highest part of the roof.

✓ The height of your kitchen extension must not go beyond four metres.

✓ Kitchen extension that’s more than one storey must not go exceed the rear wall of the main house by more than three metres.

✓ Two storey kitchen extensions must not be closer to rear boundary by anything less than seven metres.

✓ The kitchen extension must not include balconies, verandas or any raised platforms.

Over the years there has been an increase in the recommended thickness of loft insulation by the government. Obviously, the reason behind this is pretty simply - the thicker the layer of your loft insulation the bigger your savings. The UK government is very keen to every house in the country to have loft insulation fitted where possible as it helps to minimize the heating demands of these properties. Households get to benefit from loft insulation in so many ways which includes reduced energy energy bills as well as having a home that stays at a more comfortable temperature for longer.

Generally, for the government energy efficiency is crucial as it implies that the highest demand ( which is usually the time of the day when gas or electricity use is at its peak ) reduces, since each building requires slightly less energy. Overall, that ultimately implies that new power plants don’t have to be built which is some nice cost savings for the government.

In the 1980’s, any thickness of loft insulation from 25 mm to 50 mm was considered the standard. But then, building regulations stated that homes should have as much as 100 mm of loft insulation. Over time, this gradually increased to 270mm for new builds and also recommended for other properties, although not essential. As a result of this, there’s always a need to check how much insulation you currently have in your loft before you decide to purchase more. You may discover that you already have something within the range of 20 mm to 200 mm up there and knowing this and the insulation values will assist in determining how much more you’ll need to purchase, if any at all. You should also note that some modern materials can offer the same thermal insulation whilst not being as thick.

What Is Plasterboard?

The plasterboard is unarguably one of the most common building materials across the globe. Sometimes referred to as gypsum board, gyprock, drywall or wall board, the plasterboard is mostly incorporated for ceiling cladding and interior walls in several homes and offices in recent times. However, despite its global acceptability, it’s a very misunderstood building material.

The plasterboard is manufactured using a gypsum core with a heavy paper covering both sides of the sheet. The measurement of a standard plasterboard sheet is a length of 2.4 metres in and a width of 1.2 metres, with a thickness of about 13mm. The board usually have either a bevelled or a bit flat edge. The bevelled edge makes it easy for the installers to use a plaster to smooth out the surface after nailing the sheets to walls and ceilings as well as taping the edges.

The plasterboard comes in different types. Although various manufacturers provide a unique name for their products, but they’re all included in one of the following categories:

• Water Resistant Plasterboard - This type of plasterboard are best suited to be used in water areas like bathroom, laundry rooms and kitchens.

• Acoustic Plasterboard - Due to its sounding proofing qualities, this type of plasterboard is preferred to be used in home theatres or noisy areas.

• Flexible Plasterboard - This is to be incorporated on curvy surfaces.

• Fire Resistant Plasterboard - Just like the name implies, this type of plasterboard is best suited for use in high fire hazard areas.

If you’re about to kick start some small renovations around your house or office, using a plasterboard to clad your walls is a very simple and worthwhile task. However, if you want to do major renovations or need to apply plasterboard to your ceiling, the best option would be to leave it to a seasoned professional.

Before the commencement of any project, it’s always best to get an estimation of the cost. However, determining the cost of an external solid wall insulation is not the easiest of tasks as it relies on varying components such as the insulation materials to be used, labour cost and installation as well as the type of decorative finish to be incorporated. And depending on your choice of insulation material, some may need some adhesives while others may require some fixings which also contributes to the differences in price. As a result, the determination of the material cost alone can be tricky and even more so when various materials cover varying areas.

With that in mind, the cost of external solid wall insulation generally ranges between £80 to £100 per square metre2. As a result, a small flat can cost from £6000 to £9000 whereas a large detached house can have a price ranging between £21000 to £23000. To earn back your investment in terms of energy bill savings can take a couple of years, but it’s surely worth the try as there are several other benefits associated with installing an external solid wall insulation system. What’s more? Another huge factor that can influence the cost of your system is also the amount of work that’s required, how easy it is to be accessed by the installers and lots more

If you’re looking to cut down on the cost of your external solid wall insulation, then the best time for an installation might just be when you’re having another decorating or building project done such as fitting a new roof, window painting, installation of solar PV panels and more. This way, you’ll be able to spread the cost and have a greater value for each penny expended.

If you’re about to start your house extension project and wondering how long it’ll take to complete, you’re not alone! This is one of the most common questions that’s asked by homeowners in the UK and across the globe. However, there’s no single precise answer for this as there are multiple factors that’ll affect the length of time it’ll take to complete your home extension. These factors include the size of the construction work as well as whether you’re planning to live in the house after completion or otherwise.

For a single extension, the length of time it’ll take to complete the home extension is normally up to 3 months. So let’s break this down:

As you would have expected, the first step to be taken is the preparation of the site. You start by digging out the footing and preparing the foundation which should take about 2 weeks. This is then followed by the damp course installation as well as the fitting of any drains needed around the extension which will also take a further 2 weeks.

The 5th week will be for the construction of the external walls as well as putting the blockwork in place for the provision of the cavity wall insulation. A further 2 weeks after this, will be dedicated to the installation of the roof structure and the internal walls.

It’s at this junction that you’ll call on your weather proof installer to fit in your uPVC windows and doors. Once done, the gas fitters and electricians will have to be on site to connect power to your new extension building. Subsequently, this will be followed by internal wall plastering as well as breaking through your main house. Once the plaster is dried, decorations completed and all the required furniture and units installed, the extension is ready for use.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

When thinking about the right insulation material for your loft, some of the first few things that comes to mind is the various properties of that material as well as how good they fit with your home’s needs.naturally, you’d like to ensure that the insulation will be efficient enough to add to the overall energy efficiency of your home, however there are also other features that may not get as much attention but also happens to be equally important. As the primary function of an insulation is to blanket your house to offer a barrier against heat loss, going for an insulation material that’s also fireproof is crucial as loft insulation can burn. Although most insulation materials are fireproof, a myriad of problems can actually make your insulation burn.

For instance, fibreglass insulation is produced using glass combined with plastic polymers and is naturally resistant to fire. However, even at that you’d have to be careful with batts that are supported with foil or paper due to the fact that these materials can burn pretty quickly. Cellulose, on the other hand, is not fireproof and is required to be treated by other flame retardants in order to help reduce combustion. Some of the best insulation materials that are resistant to fire includes the following:

• Fibre glass. This is made of glass that’s spun into fibres, then combined using plastic polymers. As a result, fiberglass insulation is naturally resistant to fire.
• Mineral wool. Having a high melting temperature, this insulation material happens to be a great fit for thermal applications due to its superior fire resistant properties. In fact, mineral wool is still naturally non-combustible even if composed of recycled iron and steel by-products, or from actual mineral rock itself.