Find a Builder you can trust in Widnes.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Being a strong and durable product requiring little maintenance and expected to last over 2 decades, it’s little wonder resin is now a popular material amongst homeowners in the UK to build their driveways. However, there’s always the issue of the driveway fading, cracking or even becoming worn and tired. So is it possible to repair resin driveways? The answer is yes, a resin driveway can be repaired, however the best approach to use largely depends on the issue being faced. As a confident DIYer it’ll be very easy to do, but if you lack the confidence then calling in a professional for help would be a better option. So let’s take a look at how you can repair your resin driveways.

For cracks, the best reparation approach would be to chisel it out. Once done, then you can proceed to breaking the stones to form a rough edge. It’s important to make sure that the matrix of the stone remains unaffected. Make a new mixture of resin bound stone and pack it in tightly to the gap. While doing this, we’ll recommend making use of a plastic trowel to avoid burnishing. This fresh mixture will then create a smooth and perfect surface by interlocking with the edges. You can follow similar procedure for patches but these are larger holes or damages than cracks and as the name suggests are mostly likely to remain noticeable but will prevent further crumbling of your resin driveway.

For homeowners, who aren’t so keen about the patch repairs, you can opt for an overlay especially in the event whereby the majority of the surface has failed. Although many usually shy away from this approach because of the perceived high expenses, but the fact is that the approach is actually cost effective as you won’t have the need to spend more money in the long run.

Refurbishing a house brings about a plethora of benefits. These includes an increased sale value, an improvement on your quality of life or even simply to make it more visually appealing. All these are great when you look at them, but one thing that happens to be an hindrance for several homeowners is the cost of getting the project done. You may wish to set a budget, plan and prepare before commencement of the project, but the fact remains that, when it comes to refurbishing a house, nothing is certain. In fact, it’s advised to always expect the unexpected and have a lot of cash in reserve just in case something goes wrong. There are a wide range of factors that can play a key role in the overall cost of a house refurbishment. Minor refurbishment that should cost around £30,000 can easily go up to over a whooping £150,000 for a total transformation. Most of this cost will be expended on labour, and the next most significant expense, which is sourcing materials.

In general, the cost of your refurbishment project will depend on some factors which includes the size of the project, the materials used, the refurbishment or renovation level, the location of the property, the quality of the contractor hired and lots more. To estimate the cost of refurbishing your property, you can follow these simple steps:

✓ Write down a detailed list of all the things that needs to be done per room and try to be as specific as possible.

✓ Carry out a research of the labour cost in your area as well as the raw materials’ cost (here, you can make use of guides such as home advisor).

✓ Add an extra 10 to 15 percent on top of the calculated estimate for uprisings and repairs.

✓ Talk to your contractor to get a more accurate quote.

It shouldn’t do. Most companies will do all the interior work first, and the last job to do will be creating the opening from the house to the conversion. A reputable company will make sure they cause as little disruption as possible during this time.

If your basement has a cavity drain membrane, it’ll need a pump to move water away from the exterior of your basement and prevent flooding.

Sump pumps can be noisy, but they don’t have to be. Generally, if you have a well-designed pump that’s installed correctly, you shouldn’t find it a problem. For best results, hire a skilled, experienced professional to supply and install your drainage system.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.

If you’re considering rendering your house or property, then you’d most likely want to know whether or not applying for a planning permission will be needed. In several cases, planning permission will not be required for the maintenance, repair as well as replacement of the existing render on your building. These activities are covered by what’s called “Permitted Development Rights, which allows you to carry out some activities without having to apply for a planning permission but always subject to following some strict guidelines. For rendering, as long as the material (render) possesses an identical appearance to those existing on the house as well as same colour, then you will not require a planning permission. However, there are a number of projects that have been highlighted in which a planning permission would be required. These includes the following:

✓ Re-rendering in a colour that different from the original one used on the house or building.

✓ Rendering over brickwork which was not originally covered.

✓ Rendering over pebbledash

✓ Removing pebbledash and replacing it with render.

Another exception to the Permitted Development rights are for houses in conservation areas, national parks or areas of outstanding national beauty.

Although, you wouldn’t normally require to submit a planning application for approval before you apply render, but in truth it’s actually a bit of a grey area which isn’t totally clear and doesn’t allow for much freedom or creativity. And due to this fact, homeowners who wants an absolute peace of mind may opt to apply for planning permission just in case. It’s also worth noting that whether or not a planning permission is required, a huge rendering work will need to comply with building regulations which includes the need to insulate walls on the inside or outside as part of the work on several older properties .

How To Put Up Plasterboard

Putting up a plasterboard is a vital process when it comes to home renovations. However as daunting as it may seem, with a good guide and regular practice you can master the skill within a small period of time. If you lack proper training and experience, we’d recommend you hire a seasoned professional plasterer for help so as to get the best result and also avoid additional costs due to possible damages.

Putting up plasterboard is way quicker than wet plastering and also significantly reduces the drying time that can slow down your renovation plans. With a plasterboard, you can delve straight into the decorating stage and achieve a smooth finish. Below are the steps required to put up a plasterboard.

• The first step is cutting the plasterboard to shape which be one of the most challenging parts of the process. This is because you’ll need to fit the board around things such as plug sockets and window sills. As a result, this involves cutting complex shapes rather than just a simple straight line. To get this done, simply mark out the cut required with the use of a tape measure, combination square and spirit level for a better precision. Once done, you can then use a plasterboard pad saw to cut along the marked spots.

• After you made the required cuts, the next step is putting up the plasterboard. And depending on where the boards are going to be put, this could be a very challenging task. If you’re going to put the boards on the ceiling or somewhere very high up, you’d probably need an extra pair of hands for help. To get this done, use the appropriate screws to secure the boards in place if you’re installing them directly on studs. However, if you’d be fixing them onto bricks or blocks, a drywall adhesive is your best bet.