Find a Builder you can trust in Banff.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

Asides the questions relating to planning permission of a loft conversion as well as the total cost of completing a loft conversion project, this is perhaps the most common question on the loft conversion subject matter. Before making an investment decision, many homeowners will want to know just how disruptive a loft conversion is. Well, we’ve all heard the several horror stories when loft conversion builder with dirty boots tramples all over the fresh and just-acquired shag pile or the noise of the construction loud enough to annoy neighbours from four blocks away or an obvious shortage of teabags, sugar and lots more. Good news is, the disruption of loft conversion is not as bad as people make out. Let’s have a look at how it works!

Just like all other major building projects, a loft conversion is disruptive to your property. However, no two loft conversions are the same, therefore some are certain to be more drastic and invasive than others. In the long run, the project is worth the stress and inconveniences caused and in most cases, it’s usually a very good investment.

Normally, an average loft conversion is expected to last for about 9 to 12 weeks (depending on the complexity of the loft conversion project some might take longer). Some of the factors that affects the duration of a project includes the type of the loft, the design of the loft as well as the style of the property.

Generally, a loft conversion is a lot less disruptive than say completely moving a home. It all has to do with how you’re able to deal with it as a person. And besides, the effect it’s going to have to a large extent depends on the company you hire. A good company will always look to ensure to keep disruptions to a minimal when carrying out the loft conversion project.

Being a strong and durable product requiring little maintenance and expected to last over 2 decades, it’s little wonder resin is now a popular material amongst homeowners in the UK to build their driveways. However, there’s always the issue of the driveway fading, cracking or even becoming worn and tired. So is it possible to repair resin driveways? The answer is yes, a resin driveway can be repaired, however the best approach to use largely depends on the issue being faced. As a confident DIYer it’ll be very easy to do, but if you lack the confidence then calling in a professional for help would be a better option. So let’s take a look at how you can repair your resin driveways.

For cracks, the best reparation approach would be to chisel it out. Once done, then you can proceed to breaking the stones to form a rough edge. It’s important to make sure that the matrix of the stone remains unaffected. Make a new mixture of resin bound stone and pack it in tightly to the gap. While doing this, we’ll recommend making use of a plastic trowel to avoid burnishing. This fresh mixture will then create a smooth and perfect surface by interlocking with the edges. You can follow similar procedure for patches but these are larger holes or damages than cracks and as the name suggests are mostly likely to remain noticeable but will prevent further crumbling of your resin driveway.

For homeowners, who aren’t so keen about the patch repairs, you can opt for an overlay especially in the event whereby the majority of the surface has failed. Although many usually shy away from this approach because of the perceived high expenses, but the fact is that the approach is actually cost effective as you won’t have the need to spend more money in the long run.

It shouldn’t do. Most companies will do all the interior work first, and the last job to do will be creating the opening from the house to the conversion. A reputable company will make sure they cause as little disruption as possible during this time.

The best way to go about converting a basement depends on its current condition and what you’d like to use it for.

If you’re happy with its size and structure, and just want to turn it into useful storage space, then your project shouldn’t be too complicated. You’ll simply need to make sure it’s damp proof and waterproof – either by fitting tanking or a cavity drain membrane with a sump and pump. You may also need to invest in new flooring, fit basic lighting, and plaster and paint the walls and ceiling.

If you’d like to turn your basement into living space, then you’ll need to think about ventilation, insulation and heating. If this involves creating a kitchen or bathroom, you’ll also need to incorporate plumbing.

If you want to extend your basement, add lightwells, or fit windows and a sunken garden, this makes things much more complicated. You’ll probably want to hire an architect or basement conversion building specialist to help you with the design and planning, and you’ll need a structural engineer to help you ensure your property is sufficiently supported.

A patio is an outdoor space which can be used for a variety of stuffs which includes fun time with family and friends, reading time or just relaxing as the fresh breeze blows. With all these benefits and more, it’s becomes more obvious that there’s a need to keep your patio in a tip top condition at all times. If otherwise, you may not be able to enjoy your patio to your satisfaction and probably, for as long as you would want. You simply have to provide it with a regular maintenance which involves inspecting and identifying the damages that needs to be repaired before it gets out of hand. Fortunately, the minor repairs can be done by yourself if you’re confident enough. However, for bigger damages it’s advisable to call in a professional for help. In this article, we’ll take you through the patio reparation process.

✓ Prepare the area. This involves removing the problem piece gently and carefully. If there’s a piece you think can still be useful, store it in the re-use pile or you can start a new one. Once you’re done removing the pieces, the next thing to do would be to start removing anything that’s unwanted from the damaged area like debris, unwanted soil etc, and start sand fitting with some fresh sand. This should be levelled out to ensure there’s no bumps.

✓ With the sand down, you can start by putting the pieces back in together. This should be done gently to avoid any further damage. Do this until your patio

✓

Any residential building work requires a general builder. The term Residential building work means any work which is involved in building a house or changing or adding to a home. It also comprises of mending, refurbishing, ornamenting or applying shielding treatment to home. A dwelling is defined as a building or a part where people live. This might include an apartment, house or a townhouse.

Here is a list of some of the works that require a building licence:

• construction of a garage, carport or a shed

• renovation for bathroom, kitchen or laundry

• structural landscaping and building swimming pools

• construction of conservatories and atriums

• house lifting for example, raising the height of an existing structure permanently

• removing and resitting dwellings

• steam rooms and saunas.

General building contracts might also involve work that needs a specialist. These works can be appropriately subcontracted. However, this work must be carried out by the container of a permitted contractor licence or competent administrator certificate in that specialist category.

There are a number of different categories of licences that are available depending on whether you want to oversee the work or have an agreement with another party. When you have a contractor licence, you will have the option of submitting a contact to bid on the work. You can only do the categories of work designated on your licence card. Contractor licences can be allotted to people and businesses and partnerships.

With a certificate of a qualified supervisor, you will be able to supervise the type of work specified in the certificate. Such certificates are only issued to individuals and do not allow you to contract for work.

The licence of an endorsed contractor is issued to those individuals who have applied for a contractor licence but also possess the necessary qualifications and experience to become a qualified supervisor.

The simple answer to this question is... they can be! Although there are many types of porch designs that are available in the market, the uPVC porch happens to be one of the most loved and cost effective. Most home and property owners prefer the installation of a uPVC porch for a number of reasons. These includes:

• Value for money

It’s no coincidence the uPVC is widely accepted across the building industry with a plethora of uses. Not only is it relatively inexpensive to manufacture, but even the recycled uPVC is now becoming more and more useful. UPVC’s main rivals are wood and aluminium, and both are way more expensive to incorporate for frame profiles. Therefore, making use of uPVC is going to make your initial costs relatively low.

• Life Span

Although the main rivals in both hardwood and aluminium can also boast a lengthy lifespan just as uPVC. However, considering the price that you can get a uPVC, the lifespan is just incredible as it can be measured in decades.

• Aesthetic Appeal

UPVC gives you a wide range of foil colours that’ll fit your home perfectly well while also enhancing it’s visual appeal. You can actually get a porch that looks exactly like it’s manufactured from timber frames. To achieve this, all you need to do would be to make use of a wood grain surface finish. This is also long lasting, strong and resistant to fade.

• Little Maintenance

This is a very common feature of uPVC that makes it even more advantageous when used in making a porch. Unlike timber or wood which swells due to absorption of water or shrinks, you’ll never need to worry about all these distortions and more with uPVC. No painting, no sanding and ultimately, low maintenance required.