Find a Builder you can trust in Radstock.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

External wall insulation works to keep your home cosy and comfy while also helping to cut the energy bills. However with the great benefits also comes great costs, so it’s actually a logical decision to know whether there are grants out there which you’re eligible for to help you handle the cost of the external wall insulation.

There are grants available for external wall insulation, but rarely will you find one that covers the full installation cost. With the help of the government’s Energy Company Obligation (ECO) scheme, a couple of energy companies assist in making your home more energy efficient by offering grants or free insulation. In certain cases whereby you receive particular state benefits, you may as well qualify for a higher grant that’ll cover more of the insulation cost.

However, if your energy supplier doesn’t offer any grant, you need not worry as you can save as much on energy bill after installation. Here’s what insulation can help you save per year on energy bills:

• Floor insulation can help you save within a range of £30 to £75 each year.

• Cavity wall insulation can help you save about £85 to £280 a year.

• Loft Insulation (270mm) can help you save about £135 to £250 a year.

Generally, the amount you’ll be able to save on your energy bills depends mainly on the type and size of your property, as well as how energy efficient it already is without the insulation. In the long run, your external wall insulation will more than give you back your investment on the valuable project through your savings on energy bills. In other words, whether or not you’re eligible for a grant should never stop you from installing an external wall insulation.

If you’re thinking about refurbishing your house or property but don’t know how to go about it, then you’ve come to the right place. In truth, not every home refurbishment works goes in exactly the same order, however it’ll do you some good to abide by a specific plan in order to avoid both unnecessary works as well as expenses. For instance, how would it feel if you have already closed walls and paint only to realize that there’s a need to include a new plumbing stack that has to go behind the wall? Not good, right? Well, this guide is designed to help you avoid such frustrating situations. Let’s have a look!

✓ Establish a plan. This involves carrying out a good assessment of what you’d like to refurbish and set the priorities like deciding where to start and making sure you have both the time and budget to complete the project.

✓ Set a budget. Establish a final amount that’ll be the threshold to your spending. It’s always good to add an additional 10% to 15% to cover unexpected costs.

✓ Hire a contractor. Carry out a research, reach out to many contractors, compare their prices, work quality as well as integrity before hiring.

✓ Talk to your insurance company. Find out if you have the amount of coverage that suits your needs from your insurance company before and after your project.

✓ Secure permits and order materials. Make sure you check with the latest regulations before commencement. Once done, you can start ordering the required materials.

✓ Start demolition. This is optional as it only applies if space is being added.

✓ Work behind the walls. This include doing all the works necessary behind the walls like plumbing, electrical, heating etc.

✓ Paint and install flooring

✓ Fit in the cabinetry

✓ Add finishing touches. This includes the last details and decorations.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

When it comes to extending a home, the rear of the house often comes to mind a lot more than the front. However, this doesn’t mean that you can’t extend the front of your house. This can be done either as part of a renovation project whereby the entire house is incorporated or it can also be done in isolation. It’s possible to extend the front of your house without the need to apply for a planning permission, however, there are a bunch of limitations you’d have to comply with if you wish to carry out with such a project. Sometimes, this may imply that extending to the front of your home is more tedious and tasking than extending your home’s rear. So exactly how far can you extend the front of your home without planning permission?

The short and simple answer to this question is 2 metres square area with a height not more than 3 metres. Generally, you do not need a planning permission to build a front porch as long as its area doesn’t go beyond 2 square metres from a public road or walkway. Also, a tiled or slated roof can be as much as 4 metres but other roofs must not go beyond 3 metres in height. If you want to extend the front of your home beyond the restrictions specified, then you’ll have to apply for a planning permission.

Extending the front of home can be quite costly, but this can be controlled by not building to the extension to the highest specification, not including an extension on kitchens or bathrooms and more.

It shouldn’t do. Most companies will do all the interior work first, and the last job to do will be creating the opening from the house to the conversion. A reputable company will make sure they cause as little disruption as possible during this time.

There are many different types of extension. For example, you could install an orangery, flat or pitched roof extension, over-structure extension, single or double storey extension or a glass box extension. Which one of these is most suitable will depend on your existing property.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.