Find a Builder you can trust near you.

If you’re considering adding a two storey house extension, then setting a budget for this project would be a great way to get started. Similar to a rear extension, a two storey extension usually leaves the rest of the building needing some work and, due to its size, this may imply the re-development of the entire house - which is why they can be very costly. Some of the other influencing factors that can have big impact on a two storey house extension cost includes: your location, the size of the build, complexity of the design ( anything beyond the standard build will normally require more expertise and time), the glazing to be incorporated ( the more the glass used in the project, the more the material cost), as well as the team used.

Generally, when it comes to extensions, the major part of the expenses will be made on the build of the project. This is because it doesn’t only cover the material cost but also the contractor’s overhead as well as the daily rates. At this stage, the extension prices can be determined by the standard of the work that’s being done.

For a fairly average room size of about 18 square metre, the two storey extension should cost within the range of £2,500 to £3,000 per square metre - with the range being determined by the finishes incorporated. Therefore, a two storey extension of about 18 square metre should cost within the range of £45,000 to £55,000. However, this is with the assumption that there are standard window sizes, bathroom suits are modest, and without any need for any purpose joinery or glazing. If you wish to include all these extra features you’ll also have to pay more to make the total cost between £70,000 to £80,000.

If you’re planning to construct a kitchen diner extension, to help you set a budget and start planning you must first have a cost estimate that’ll complete the entire project. If not, there’s a probability that you may have to spend more than would have been necessary or probably break the bank to have the project done. In truth, there’s no single and short answer to this question as the cost of a kitchen diner is largely dependent of several variables. In this article, we’re going to give a good insight into kitchen diner extension cost so as to help you make informed decisions moving forward. Let’s take a look!

On the average, a kitchen diner extension will cost within the range of £25,000 to about £45,000, however if you happen to reside in London, you can expect the cost to be a lot more than that - closer to £60,000. And due to the fact that there happens to be a plethora of options out there, any decision to make be it on the size, tradesman, flooring, finishes or type of the kitchen diner extension, will have a considerable impact on the overall cost of the project. For instance, a basic kitchen diner extension cost can be within the range of £12,000 to about £15,000., while a high end kitchen diner extension can reach a whooping price between £80,000 to about £100,000.

The total cost of your kitchen diner project will rely heavily of the size as well as the quality of the finishes. For example, a kitchen diner extension that’s small and basic is likely to cost about £1,300 to £1,500 per square metre. However, if you’re going for higher quality finishes, you can expect to pay within the range of £1,900 to about £3,000 per square metre.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Did you try rendering a wall but it doesn’t turn out the way you would have hoped for? Or perhaps you’ve been watching your wall render gradually deteriorate over time. Regard of your purpose, learning how to repair render cracks on wall is usually a great skill to have with your home maintenance in mind. However, whenever these crack are too large or difficult, we’d recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the wall render repairing process. Let’s have a look!

No matter how solid a building material is, over time it’ll yield to the elements. When it comes to wall rendering it may be a case of too much sunshine or a costly mistake in the application process, but in truth, it cracks just because it cracks.

In order to repair render cracks, you’d have to start with a removal of damaged or cracked render. You’ll have to remove all the render or just a small section depending on the area you’re working on. If you’re able to clean all of the existing render as well as the paint over it all (both old and new), then removing a small section would work better as it makes it look neat and redone. Upon the removal of the existing render, the next important step would be to remove all loose material as well. Once done, you can then leave for up to 2 days to allow any trapped moisture to come out. Unfortunately, if the rains you’d have to wait till that dries too before you proceed.

Once dried, you can buy a pre-prepared render mix which already contains cement, lime and sand. Mix a 20kg bag with 4 litres of water (or check the product instructions and follow strictly), the mix to a fine consistency. Render is quick to dry, so you’d want to apply within 30 minutes of mixing. Make use of a trowel to apply the render on the affected spots and blend with the surrounding area.

Cladding comes in a range of styles, such as flush, shiplap, and featheredge. Many types of cladding are also available in a variety of colours to suit any property. A cladding specialist will be able to discuss what solution is best for your property and how it works.

It shouldn’t do. Most companies will do all the interior work first, and the last job to do will be creating the opening from the house to the conversion. A reputable company will make sure they cause as little disruption as possible during this time.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the ours so that you can find quality tradespeople and see genuine reviews from previous customers. Not all online review sites can be trusted to display real reviews.

With the numerous benefits that comes with the installation of an external wall insulation in a building, it’s also important to find out whether it’s also safe before proceeding to fit one in your home. Firstly, to ensure that external wall insulation systems are safe, they must be BBA approved, which means they’ve been subjected to a thorough testing by the British Board of Agrement and therefore, suitable for use in UK homes.

Given the fact that cladding materials have recently generated a lot of debate and negative press about how reliable some particular materials are, questions are being asked of the safety and reliability of external wall insulation. However we must clarify that, although external wall insulation can be classified under cladding, it is very different to rainscreen cladding - which caused the Grenfell fire tragedy.

External wall insulation is completely safe. However, when it comes to fire, the safety of your system depends largely on the insulation type in question. The safest type of insulation you can have installed is the Rockwool insulation boards which are rated as Euroclass A1 non-combustible. The board is specially designed in such a way that it contains fire - preventing it from reaching the other areas of the building. They also do not produce harmful emission or smoke when impacted by fire.

Meanwhile, the Wood Fibre, is also a great insulation which is known to char and not burn. Contrary to many beliefs, it actually burns slowly creating this charring effect which produces an oxygen barrier that helps reduce the spread of fire.

To make your system safer, you can also make use of Fibreglass Mesh for reinforcement. It helps to improve the strength of the tensile which promotes the security of the boards attached to the wall.