Find a TV Aerial Installer you can trust in Axbridge.

Your TV and aerial need to be connected by coaxial cable for your TV to work. Most properties have wall mounted connection boxes – similar to electrical plugs – that you can simply plug your TV into. If you don’t have a cable, it’s easy to pick up one from most DIY shops.

If you’re installing a new outside aerial, you may be able to reuse the old cable. If you can’t, you’ll need to route a new one down from your aerial to any sockets you need. Coaxial cable can be routed down the exterior of your property, through loft spaces, under floors and along skirting boards.

Have you decided to upgrade to Sky’s next generation TV service - Sky Q?  Well, with the 1080 picture quality and a resolution of 3840 which enables you to enjoy your favorite shows in the highest quality, who wouldn’t want to have one installed in his/her home? Apart from the above benefits, you’re also given the ability to record up to 6 shows any time you want, while still viewing a 7th. For many individuals who wish to have the Sky Q installed in their homes, one major concern they all have in common is determining whether or not a satellite dish would be needed. In this article, we aim to help you resolve this once and for all.

The short and simple answer to this question is yes, you’ll need a new satellite for sky Q. However, we’ll strongly recommend you hire the services of a professional and experienced engineer who is well trained and skilled when it comes to the correct and safe installation of satellite dishes. They’ll ensure the entire process goes smooth without any form of interruption. With that, you can be sure to get the best possible quality display from your sky Q system while also avoiding any form of potential installation or placement issues with your dish.

In general, the sky Q installation process is relatively quick and system. As soon as you obtain your viewing card from Sky, your engineer can start setting up your TV with sky Q.

Basically, what a tv aerial does is simply to receive broadcasted tv signals from the television station, then transmit those vibrations directly to your screen. Just like any other antenna, the tv aerial is made of metal. How exactly does it work?

The small electrical currents present in the antenna is induced by the electromagnetic waves transmitting tv signals. The tv set then acts as an amplifier to the signal and chooses the information which carries the sound as well as vision. The tv aerials are also commonly referred to as “yagi arrays by engineers. The metal plates present at the far end of the array directs the signal back down its length. Meanwhile, the parallel rod-like structures which run along the aerial’s length are designed and spaced to improve the strength of the signal.

Generally, aerials are divided into two categories – indoor and outdoor. Indoor antennas are the types located on top of your tv set or next to it, while outdoor antennas are installed on top of your building and exposed to the elements. Most times, the type of aerial you’ll require will be determined by the location of your house. For fringe or rural areas which are far from the transmission stations and likely to be blocked by natural obstructions like trees and hills, outdoor antennas are more suitable.

The performance or effectiveness of your TV aerial can be affected by a couple of things. Firstly, it can be unaligned by poor weather which will affect the signal received and interfere with the picture quality of the TV. Secondly, the TV aerial cable can also become faulty or disconnected. This is mostly the case when you get a “no signal message on your TV screen.

Does your old TV aerial cable have a cut or tear in line? Well, good news is, you don’t have to discard it. When such problems occur, they can lead to loss of conductivity or interference which results in weak or poor reception or even none at all. With a few easily accessible coaxial repair tools which can be obtained from local stores, repairing your aerial cable can require a much less effort than you think. In this post, we’re going to take you through the TV aerial cable repairing process. Let’s take a look!

• Identify the part of your coaxial cable that needs to be repaired. Incorporate wire cutters to make a clean cut across the damaged cable portion.
• Close the RG-6 labeled groove of the crimping tool an inch down the cable and make a complete cut around the exterior part of the cable.
• Cut the exposed aluminum braiding around the insulation to leave the copper filament above the cut portion which is usually surrounded by a white PVC insulation.
• Using the part of the stripping tool labeled “inner, cut between the insulation down to around 1/3 inch. Once done, twist the stripper around the section to get a clean cut and take off the portion that is cut.
• Identify the copper filament positioned at the middle of the cable and surrounded by insulation and thread it through the twist-on connector’s base.
• Strip the damaged coax cable’s other end and add a twist-on connector to it.
• Use a coupler to connect the two repaired cables. To do this, simply screw one end of the first cable to one side of the cable coupler and do the same to the second cable to the other side of the coupler

Not if your current aerial is in good condition and receives a good signal. If you don’t currently get a good signal, you may need to upgrade or relocate your aerial to receive HD channels or if your TV is not HD ready. You may need to upgrade your television if this is the case.

Generally speaking, you do need an aerial if you have a smart TV. This what will enable you to watch live TV. However, if you’re not bothered about live TV, and just want to use services like Netflix, Amazon Prime and Youtube, you don’t normally need a TV aerial. This is because these services use the internet instead.

Yes, an aerial could be installed in your garden or on outbuildings. This will depend on the strength of the signal in your area. A professional aerial installation company will be able to advise you on the possible locations for an aerial on your property.

If you’re looking at the possibility of installing a satellite dish on your chimney, then you’ve come to the right place! First and foremost, it should be noted that chimney mounts are mostly incorporated for individuals who desires the installation of an antenna at the highest point of their roofs without having to drill holes in the roof. This is quite popular as they’re able to ensure an easy installation and also works incredibly well for several antennas. What about satellite dish? Can it also be mounted on a chimney? Let’s take a look!

The short and simple answer to this question is yes, a satellite dish can be installed on a chimney. However, it must be said that this installation is not advisable. Unlike antennas, satellite dishes are aimed much more precisely. While antennas can be positioned as far as 15 degrees off the main aim before the reception is affected, satellite dishes, on the other hand, need to be positioned about one half of one degree in order to allow for a good operation. This is mainly because the broadcast tower you’re aiming your antenna at is, at most, 75 miles away compared to satellite dishes which are aimed at broadcast towers which are at least 22,000 miles away and that’s even if you happen to be directly under one.

Installing a satellite dish on a chimney will make it difficult for you to get it secure enough to have it properly aimed. This isn’t to say it won’t work at first, but most times, winds will probably drive the satellite dish off the target in little time.