Find a TV Aerial Installer you can trust in Newhaven.

If you’re looking at the possibility of installing a satellite dish on your chimney, then you’ve come to the right place! First and foremost, it should be noted that chimney mounts are mostly incorporated for individuals who desires the installation of an antenna at the highest point of their roofs without having to drill holes in the roof. This is quite popular as they’re able to ensure an easy installation and also works incredibly well for several antennas. What about satellite dish? Can it also be mounted on a chimney? Let’s take a look!

The short and simple answer to this question is yes, a satellite dish can be installed on a chimney. However, it must be said that this installation is not advisable. Unlike antennas, satellite dishes are aimed much more precisely. While antennas can be positioned as far as 15 degrees off the main aim before the reception is affected, satellite dishes, on the other hand, need to be positioned about one half of one degree in order to allow for a good operation. This is mainly because the broadcast tower you’re aiming your antenna at is, at most, 75 miles away compared to satellite dishes which are aimed at broadcast towers which are at least 22,000 miles away and that’s even if you happen to be directly under one.

Installing a satellite dish on a chimney will make it difficult for you to get it secure enough to have it properly aimed. This isn’t to say it won’t work at first, but most times, winds will probably drive the satellite dish off the target in little time.

Freeview is only available through a TV aerial. You can’t access Freeview using the internet, so you’ll need to invest in a TV aerial if you haven’t got one already.

Satellite TV is a service that provides its customers with a wide range of TV channels by transmitting signals from a communications satellite. Users around the world can pick it up using a satellite dish mounted on their property and connected to their TV. Satellite TV is particularly useful for viewers who live out of aerial and cable TV range in remote areas.

Generally speaking, you do need an aerial if you have a smart TV. This what will enable you to watch live TV. However, if you’re not bothered about live TV, and just want to use services like Netflix, Amazon Prime and Youtube, you don’t normally need a TV aerial. This is because these services use the internet instead.

The process you need to go through to install a TV aerial depends on the type of aerial you have. If you have an indoor aerial, it’s simple. Just plug the aerial into your TV and stand it up next to it. If the signal isn’t right, then try moving your aerial closer to a window or higher up. Make sure you rescan for channels every time you move it so you know if you’ve made an improvement. It’s also fairly easy to install a loft TV aerial – just take it up into your loft and position it in a convenient place. Again, experiment with angles and positions to ensure you get the best signal. Installing an outdoor TV aerial is a little trickier. Ideally, try to fix your aerial to a wall or chimney at a gable end – this will be much easier to access than a chimney in the middle of the roof. Follow the instructions that come with your aerial for mounting it – it’s usually best to lash your aerial on rather than use screws. If you’re not used to working at height or aren’t confident doing your own aerial installation work, it’s best to get in touch with a professional.

Does your old TV aerial cable have a cut or tear in line? Well, good news is, you don’t have to discard it. When such problems occur, they can lead to loss of conductivity or interference which results in weak or poor reception or even none at all. With a few easily accessible coaxial repair tools which can be obtained from local stores, repairing your aerial cable can require a much less effort than you think. In this post, we’re going to take you through the TV aerial cable repairing process. Let’s take a look!

• Identify the part of your coaxial cable that needs to be repaired. Incorporate wire cutters to make a clean cut across the damaged cable portion.
• Close the RG-6 labeled groove of the crimping tool an inch down the cable and make a complete cut around the exterior part of the cable.
• Cut the exposed aluminum braiding around the insulation to leave the copper filament above the cut portion which is usually surrounded by a white PVC insulation.
• Using the part of the stripping tool labeled “inner, cut between the insulation down to around 1/3 inch. Once done, twist the stripper around the section to get a clean cut and take off the portion that is cut.
• Identify the copper filament positioned at the middle of the cable and surrounded by insulation and thread it through the twist-on connector’s base.
• Strip the damaged coax cable’s other end and add a twist-on connector to it.
• Use a coupler to connect the two repaired cables. To do this, simply screw one end of the first cable to one side of the cable coupler and do the same to the second cable to the other side of the coupler

Not if your current aerial is in good condition and receives a good signal. If you don’t currently get a good signal, you may need to upgrade or relocate your aerial to receive HD channels or if your TV is not HD ready. You may need to upgrade your television if this is the case.

If your TV picture is pixelated, poor quality, or cutting out, there may be a fault with your aerial or the cables connecting it to your TV. Also your aerial may not be located in the correct place. An experienced aerial company can carry out a survey to discover the fault.