Find a TV Aerial Installer you can trust in Heathfield.

Freeview is only available through a TV aerial. You can’t access Freeview using the internet, so you’ll need to invest in a TV aerial if you haven’t got one already.

The process you need to go through to install a TV aerial depends on the type of aerial you have. If you have an indoor aerial, it’s simple. Just plug the aerial into your TV and stand it up next to it. If the signal isn’t right, then try moving your aerial closer to a window or higher up. Make sure you rescan for channels every time you move it so you know if you’ve made an improvement. It’s also fairly easy to install a loft TV aerial – just take it up into your loft and position it in a convenient place. Again, experiment with angles and positions to ensure you get the best signal. Installing an outdoor TV aerial is a little trickier. Ideally, try to fix your aerial to a wall or chimney at a gable end – this will be much easier to access than a chimney in the middle of the roof. Follow the instructions that come with your aerial for mounting it – it’s usually best to lash your aerial on rather than use screws. If you’re not used to working at height or aren’t confident doing your own aerial installation work, it’s best to get in touch with a professional.

Yes, an aerial could be installed in your garden or on outbuildings. This will depend on the strength of the signal in your area. A professional aerial installation company will be able to advise you on the possible locations for an aerial on your property.

Does your old TV aerial cable have a cut or tear in line? Well, good news is, you don’t have to discard it. When such problems occur, they can lead to loss of conductivity or interference which results in weak or poor reception or even none at all. With a few easily accessible coaxial repair tools which can be obtained from local stores, repairing your aerial cable can require a much less effort than you think. In this post, we’re going to take you through the TV aerial cable repairing process. Let’s take a look!

• Identify the part of your coaxial cable that needs to be repaired. Incorporate wire cutters to make a clean cut across the damaged cable portion.
• Close the RG-6 labeled groove of the crimping tool an inch down the cable and make a complete cut around the exterior part of the cable.
• Cut the exposed aluminum braiding around the insulation to leave the copper filament above the cut portion which is usually surrounded by a white PVC insulation.
• Using the part of the stripping tool labeled “inner, cut between the insulation down to around 1/3 inch. Once done, twist the stripper around the section to get a clean cut and take off the portion that is cut.
• Identify the copper filament positioned at the middle of the cable and surrounded by insulation and thread it through the twist-on connector’s base.
• Strip the damaged coax cable’s other end and add a twist-on connector to it.
• Use a coupler to connect the two repaired cables. To do this, simply screw one end of the first cable to one side of the cable coupler and do the same to the second cable to the other side of the coupler

Have you decided to upgrade to Sky’s next generation TV service - Sky Q?  Well, with the 1080 picture quality and a resolution of 3840 which enables you to enjoy your favorite shows in the highest quality, who wouldn’t want to have one installed in his/her home? Apart from the above benefits, you’re also given the ability to record up to 6 shows any time you want, while still viewing a 7th. For many individuals who wish to have the Sky Q installed in their homes, one major concern they all have in common is determining whether or not a satellite dish would be needed. In this article, we aim to help you resolve this once and for all.

The short and simple answer to this question is yes, you’ll need a new satellite for sky Q. However, we’ll strongly recommend you hire the services of a professional and experienced engineer who is well trained and skilled when it comes to the correct and safe installation of satellite dishes. They’ll ensure the entire process goes smooth without any form of interruption. With that, you can be sure to get the best possible quality display from your sky Q system while also avoiding any form of potential installation or placement issues with your dish.

In general, the sky Q installation process is relatively quick and system. As soon as you obtain your viewing card from Sky, your engineer can start setting up your TV with sky Q.

If you are planning to invest in a new satellite dish, then you’d probably want to know the most suitable receiver to incorporate. If you have this same concern, then you’ve come to the right place! In this post, we’re going to give you a good insight into the world of satellite dish receivers in order to help you make the best-informed decision possible moving forward. Let’s take a look!

Firstly, it must be stated that there happens to be a plethora of LNB types, makes and models available in the market today and picking the right one for your satellite is crucial as the wrong one may imply your satellite will not work. The most common LNB types are single LNBs and Quad LNBs.

The major difference between all types is the amount of output possessed by each LNB. This is what allows extra satellite receivers to be added for additional TV points as well as the inclusion of satellite PVRs which features recordable, play, pause and rewind TV services. For example, a single LNB possesses just one LNB connection for a coaxial cable to be attached. This allows you to connect a standard satellite receiver such as Freesat box or Sky. There are also dual or twin LNB, quad LNB and octo LNB which allows for two (or one satellite PVR), four (two PVRs or one PVR and two standard satellite receivers) and eight separate satellite receivers (four PVRs or combination of both) respectively. There are many other LNB types you can choose from with varying features, so it all depends on your requirements.

Satellite TV is a service that provides its customers with a wide range of TV channels by transmitting signals from a communications satellite. Users around the world can pick it up using a satellite dish mounted on their property and connected to their TV. Satellite TV is particularly useful for viewers who live out of aerial and cable TV range in remote areas.

Basically, what a tv aerial does is simply to receive broadcasted tv signals from the television station, then transmit those vibrations directly to your screen. Just like any other antenna, the tv aerial is made of metal. How exactly does it work?

The small electrical currents present in the antenna is induced by the electromagnetic waves transmitting tv signals. The tv set then acts as an amplifier to the signal and chooses the information which carries the sound as well as vision. The tv aerials are also commonly referred to as “yagi arrays by engineers. The metal plates present at the far end of the array directs the signal back down its length. Meanwhile, the parallel rod-like structures which run along the aerial’s length are designed and spaced to improve the strength of the signal.

Generally, aerials are divided into two categories – indoor and outdoor. Indoor antennas are the types located on top of your tv set or next to it, while outdoor antennas are installed on top of your building and exposed to the elements. Most times, the type of aerial you’ll require will be determined by the location of your house. For fringe or rural areas which are far from the transmission stations and likely to be blocked by natural obstructions like trees and hills, outdoor antennas are more suitable.

The performance or effectiveness of your TV aerial can be affected by a couple of things. Firstly, it can be unaligned by poor weather which will affect the signal received and interfere with the picture quality of the TV. Secondly, the TV aerial cable can also become faulty or disconnected. This is mostly the case when you get a “no signal message on your TV screen.