Find a TV Aerial Installer you can trust in Westhill.

Yes, an aerial could be installed in your garden or on outbuildings. This will depend on the strength of the signal in your area. A professional aerial installation company will be able to advise you on the possible locations for an aerial on your property.

No, you will need a satellite dish to receive a satellite signal for services like Sky or Freesat, as these are specific channels and programmes only broadcast via this medium. These can be installed in a similar way to a standard TV aerial by a recognised engineer.

The process you need to go through to install a TV aerial depends on the type of aerial you have. If you have an indoor aerial, it’s simple. Just plug the aerial into your TV and stand it up next to it. If the signal isn’t right, then try moving your aerial closer to a window or higher up. Make sure you rescan for channels every time you move it so you know if you’ve made an improvement. It’s also fairly easy to install a loft TV aerial – just take it up into your loft and position it in a convenient place. Again, experiment with angles and positions to ensure you get the best signal. Installing an outdoor TV aerial is a little trickier. Ideally, try to fix your aerial to a wall or chimney at a gable end – this will be much easier to access than a chimney in the middle of the roof. Follow the instructions that come with your aerial for mounting it – it’s usually best to lash your aerial on rather than use screws. If you’re not used to working at height or aren’t confident doing your own aerial installation work, it’s best to get in touch with a professional.

Does your old TV aerial cable have a cut or tear in line? Well, good news is, you don’t have to discard it. When such problems occur, they can lead to loss of conductivity or interference which results in weak or poor reception or even none at all. With a few easily accessible coaxial repair tools which can be obtained from local stores, repairing your aerial cable can require a much less effort than you think. In this post, we’re going to take you through the TV aerial cable repairing process. Let’s take a look!

• Identify the part of your coaxial cable that needs to be repaired. Incorporate wire cutters to make a clean cut across the damaged cable portion.
• Close the RG-6 labeled groove of the crimping tool an inch down the cable and make a complete cut around the exterior part of the cable.
• Cut the exposed aluminum braiding around the insulation to leave the copper filament above the cut portion which is usually surrounded by a white PVC insulation.
• Using the part of the stripping tool labeled “inner, cut between the insulation down to around 1/3 inch. Once done, twist the stripper around the section to get a clean cut and take off the portion that is cut.
• Identify the copper filament positioned at the middle of the cable and surrounded by insulation and thread it through the twist-on connector’s base.
• Strip the damaged coax cable’s other end and add a twist-on connector to it.
• Use a coupler to connect the two repaired cables. To do this, simply screw one end of the first cable to one side of the cable coupler and do the same to the second cable to the other side of the coupler

Have you decided to upgrade to Sky’s next generation TV service - Sky Q?  Well, with the 1080 picture quality and a resolution of 3840 which enables you to enjoy your favorite shows in the highest quality, who wouldn’t want to have one installed in his/her home? Apart from the above benefits, you’re also given the ability to record up to 6 shows any time you want, while still viewing a 7th. For many individuals who wish to have the Sky Q installed in their homes, one major concern they all have in common is determining whether or not a satellite dish would be needed. In this article, we aim to help you resolve this once and for all.

The short and simple answer to this question is yes, you’ll need a new satellite for sky Q. However, we’ll strongly recommend you hire the services of a professional and experienced engineer who is well trained and skilled when it comes to the correct and safe installation of satellite dishes. They’ll ensure the entire process goes smooth without any form of interruption. With that, you can be sure to get the best possible quality display from your sky Q system while also avoiding any form of potential installation or placement issues with your dish.

In general, the sky Q installation process is relatively quick and system. As soon as you obtain your viewing card from Sky, your engineer can start setting up your TV with sky Q.

If your TV picture is pixelated, poor quality, or cutting out, there may be a fault with your aerial or the cables connecting it to your TV. Also your aerial may not be located in the correct place. An experienced aerial company can carry out a survey to discover the fault.

Basically, what a tv aerial does is simply to receive broadcasted tv signals from the television station, then transmit those vibrations directly to your screen. Just like any other antenna, the tv aerial is made of metal. How exactly does it work?

The small electrical currents present in the antenna is induced by the electromagnetic waves transmitting tv signals. The tv set then acts as an amplifier to the signal and chooses the information which carries the sound as well as vision. The tv aerials are also commonly referred to as “yagi arrays by engineers. The metal plates present at the far end of the array directs the signal back down its length. Meanwhile, the parallel rod-like structures which run along the aerial’s length are designed and spaced to improve the strength of the signal.

Generally, aerials are divided into two categories – indoor and outdoor. Indoor antennas are the types located on top of your tv set or next to it, while outdoor antennas are installed on top of your building and exposed to the elements. Most times, the type of aerial you’ll require will be determined by the location of your house. For fringe or rural areas which are far from the transmission stations and likely to be blocked by natural obstructions like trees and hills, outdoor antennas are more suitable.

The performance or effectiveness of your TV aerial can be affected by a couple of things. Firstly, it can be unaligned by poor weather which will affect the signal received and interfere with the picture quality of the TV. Secondly, the TV aerial cable can also become faulty or disconnected. This is mostly the case when you get a “no signal message on your TV screen.

Your TV and aerial need to be connected by coaxial cable for your TV to work. Most properties have wall mounted connection boxes – similar to electrical plugs – that you can simply plug your TV into. If you don’t have a cable, it’s easy to pick up one from most DIY shops.

If you’re installing a new outside aerial, you may be able to reuse the old cable. If you can’t, you’ll need to route a new one down from your aerial to any sockets you need. Coaxial cable can be routed down the exterior of your property, through loft spaces, under floors and along skirting boards.