Solid Fuel Boiler in Invergordon

As an environmentally conscious homeowner, it’s very likely you would have heard of a wood pellet boiler or maybe even considering fitting one in your home or property. So if you’ve heard about wood pellet boilers, you’d probably want to know about it especially how it works. In this article, we’re going to walk you through the wood pellet boilers operating process. Let’s take a look!

✓ Typically, wood pellet boilers possess 4 major components, these includes a burner ( which ignites or burns the pellets), a hopper ( which stores unused pellets), a conveyor ( which works to carry the pellets from the hopper to the burner where its ignited) and lastly, a controller ( which responds automatically to your thermostat and appliances’ demands).

✓ In the event whereby your thermostat demands heat or if you happen to switch on a hot water tap or appliance, pellets will be automatically fed into the burner which in turn ignites it and set the firing rate to match the needed heating load.

✓ In a situation whereby more pellets is needed by your boiler, the vacuum or augur system will act by pulling pellets from your bulk pellet storage bin and automatically refill itself.

✓ The wood pellet boiler will clean the burn pot and heat exchanger areas ( moving ash into the ash bin), during and after the burn cycles. The ash bin will be emptied once for every 2 to 3 ton of pellet that’s ignited.

Other facts about wood pellet boilers

✓ The wood pellet boiler can be directly linked to existing plumbing and heating system, regardless of whether or not there’s an existing heating oil boiler remaining.

✓ Wood pellets can be stored in bulk in a storage bin outside your home as the bins are generally weather resistant and also very durable.

If you’re looking to warm up your household to ensure your comfort all year long, there are actually a wide array of heating systems out there that you can put into consideration. However, in this article, we’ll be taking a look at gravity feed boiler and how it works.

A gravity fed heating system is basically an all water based hydronic heating ( both hot water and steam) that makes use of the natural gravity attributes of heated water as well as water vapour to distribute energy. Normally, this type of heating system possesses a cold water tank in the house’s loft or attic with a boiler on the ground floor as well as a hot water cylinder which is usually somewhere between these two components.

In the event whereby there’s a call for water, the boiler is going to fire up and warm a large volume of water. And due to the fact that cold water is a lot denser than the newly heated water, it’s able to drop down to the boiler. Subsequently, the heated water is transported up to the hot water cylinder from where it is forced out and distributed to the hot water taps. If there happens to be a heat request during this period, the heated water will be transported to the radiators with the help of a pump. As a result, when it comes to gravity heating system, it’s simply impossible to have heating in the absence of hot water. this is of course unless you’re making use of C Plan which features 1 zone valves alongside 6 wires. These kind of system are, however, usually operated by programmers that automatically switch hot water on any time there’s a heat request.

Solid fuel engineers are everywhere, but finding one nearby for your project can be tricky and stressful, with both cost and reliability coming into question. This is even more worrisome when you’re fully aware that your solid fuel heating system potentials can only be fully maximized depending on how well it’s installed and how good your engineer or installer is. If you’re also facing the same challenge, then you’ve come to the right place. In this article, we’ll share with you some tips on how to choose a nearby professional and reliable solid fuel engineer who’ll ensure you get immense value for every penny spent. Let’s take a look!

✓ Ask for recommendations. To find a tradesperson, not just a solid fuel engineer, personal recommendations is the best way to go. Installation of a solid fuel heating system is a major undertaking which comes with a lot of costs, so if you’re going to do it the least you can do is ensure you do it right. Carry out your research, ask friends and family, neighbours and loved ones if the know of any reliable solid fuel engineer in the local area. If they’ve have one they’ve used, you can request for the cost, quality of the job done, the duration of the project and any other detail you feel you should know.

✓ Store contact lists. You’ll discover a long list of solid fuel engineers on many stores selling solid fuel boilers. These installers may not be affiliated with the store owners, but many stores see it as their responsibility to point you in the right direction so that the boilers acquired from them can be put to good use.

✓ Internet. With the rapid rise of online technology, there’s hardly a service you can’t find on the internet. Websites like Quotatis have been helping people find their desired service providers with relative ease for so long. To get the right solid fuel engineer online, it’s advisable to check reviews as well as testimonials before moving forward.

First and foremost, HETAS simply refers to Heating Equipment and Testing Approval Scheme. Several solid fuel and wood biomass appliances and systems’ installations are subject to the specified rules of Building Regulations while also being notifiable to the Local Authority in your area by the law. HETAS registered installers are able to self-certificate projects carried out by themselves which helps to prevent the need for the expensive and time consuming Building Notice application which would be made to the local Building Control Department.

Therefore, there are a number of benefits that you stand to derive by hiring a HETAS engineer to fit your solid fuel boilers. Now let’s have a look!

✓ HETAS is the only competent engineers scheme that specializes in solid fuel as well as wood biomass.

✓ All registered installers by HETAS are properly trained and assessed to be competent to carry out a great job.

✓ HETAS offers both technical and regulatory support to registrants.

✓ The HETAS scheme covers all the scope of work that an installer should be able to carry out such as dry appliances, solid mineral, wood biomass, appliances with boilers, wood, hot water and heating systems as well as re liningof chimneys.

✓ HETAS also publishes and makes available the list of approved appliances, fuels and equipment in order to help consumer, installers as well as the specifiers in selecting an installation that perfectly suits the consumers’ needs, while also complying the the provisions of the Building regulations and safety standards.

✓ HETAS also makes available the lists of installers, flue professionals, chimney sweeps as well as maintenance companies to help you to safely maintain your installation into the future.

✓ HETAS also helps consumers in resolving any problems of complaints in such a way to promote a fair and equitable result.