Roof replacement (Pitched/Tiled) in Craigavon

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Replacement of roof tiles that have fractured, cracked or is missing is vital to avoid roof leaks and ceiling damage once rain and wind appear. Countering the problem swiftly by yourself is probable as long as it's only a few tiles. Charges for tile replacement can be expensive and fluctuate conditional on the company you hire.

The steps to replacing a tile are:

Ensure you have the right replacement tile as there are numerous different roof tiles on the market.

The most common types of roof tiles are concrete and terracotta. You must confirm that the tile is identical to your earlier tile or it may not work and can result in impairment even though you've tried to repair it. If you don't know what the tile is, ask the suggestion of a roofing supplier and they should be able to match it for you.

Get onto the roof.

It is only advisable to do this if the safety is guaranteed, using a steady ladder and maybe even using climbing ropes to protect you in case of a fall. If you don't possess a head for altitudes or you're sceptical about how safe it is for you to get on the roof, call in a professional.

Once you have securely gotten to the cracked tile, you'll want to somewhat lift the tiles that overlay the one to be detached. Do this by means of two pieces of timber to hold them up. Lift the broken tile over the baton with a brick trowel and gently slide it down.

Place your new tile on top of the brick trowel and inverse the steps to remove the tile.

Be certain to place the overlying tiles back into place.

Conduct a fast check across the roof to review any other possible damage. It is always advised to keep update on how the roof is holding out to keep an eye out for other tiles that might need replacing.

One of the most popular choices for roofing materials are roof slates. There is a number of advantages that a roof slate has, hey can be aesthetically pleasing, they can also increase the potential selling value of the house and many more. Slate is a sturdy and resilient material that delivers waterproofing physical characteristics to a pitched roof. Unlike other roof materials which absorb water slates do not. Therefore, slate is the most resistant towards freezing and water damage.

Find out the pitch of your roof

Before beginning with the fitting procedure, you need to figure out the pitch of your roof. The roof pitch commands how much overlap is essential with each slate. This has been made a lot easier than the early days with the advancement of technology.

Find out the required overlap

Once you’ve found out the exact pitch of your roof accurately, take a look at the slate producer’s description. Each manufacturer will propose the obligatory overlap in order to form a firm and safe slate roof.

Roll out the roof membrane

Firstly, guarantee your joists or trusses are clean of any sheards or old nails that could harm the membrane. You will now have to roll the chosen roofing membrane along the roof trusses. It is always wise to start from one of the bottom corners and keep rolling it along to the other corner.

Secure the roof membrane

Once the membrane has been moved out, use thump nails to protect one edge. You will now have to pull the membrane taut and carefully fix it into position. Do this before adding any nails across the membrane at points of intersection with the trusses for extra stability.

Batten placement

This is done to find the proper assignment of the battens. For this, you will need two full-sized slates along with an under eaves slate. Carefully position the battens on the top of the roof on the top of the overlay. Make sure not to fix them down since it will be easier to move them around and make any adjustments.

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.