Porch in Worcester Park

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

A front porch is a glorious addition that would be a blessing to have in any home. It gives you a good floor space to enjoy your neighbourhood as well as your surroundings in the cool atmosphere of the outside living space. The question however is, how do you build a porch? Constructing the structure can be a very challenging task but with proper guidance and lots of practice, you can also be a skilled porch builder. To protect your investment, it’s advisable to hire the services of a professional for help with your porch especially if you lack proper training and experience. This way, you’ll get to save time and money. This guide is prepared to give you some insight into the porch building process.

lAssess Your Location

• Consider the location before proceeding with the project. It’s essential to select a location that’ll reduce the sunlight coming in.

lPlan The Materials Required For Your Porch

• You’ll have to decide the type of porch you’ll be going for. For example, your porch can be built out of wood, composite decking or if it’s going to utilize some stone flooring, brick or even tile.

lBuild Your Porch Foundation

• Dig the foundations deep to ensure stability while also putting in mind any pipework or cabling

• Fit a damp proof course

• Add the subfloor - this can be concrete or timber

lStart To Lay The Brick And Floor

• Lay the bricks evenly up to the DPC level

• Lay the floor

• Add the flooring protection

• Once done, you can lay the bricks to the window level

• You can fit in a window sill if required before proceeding the brick and block work until it reaches the roof timber’s height

• Fit the linter when you get to the top of where the window will reach.

lConstruct The Roof

• Build a timber framework

• Fit a breathable roof membrane

• Install the roof battens and lay the roof tiles.

• Add gutters

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.