Porch in Dingwall

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

The simple answer to this question is... they can be! Although there are many types of porch designs that are available in the market, the uPVC porch happens to be one of the most loved and cost effective. Most home and property owners prefer the installation of a uPVC porch for a number of reasons. These includes:

• Value for money

It’s no coincidence the uPVC is widely accepted across the building industry with a plethora of uses. Not only is it relatively inexpensive to manufacture, but even the recycled uPVC is now becoming more and more useful. UPVC’s main rivals are wood and aluminium, and both are way more expensive to incorporate for frame profiles. Therefore, making use of uPVC is going to make your initial costs relatively low.

• Life Span

Although the main rivals in both hardwood and aluminium can also boast a lengthy lifespan just as uPVC. However, considering the price that you can get a uPVC, the lifespan is just incredible as it can be measured in decades.

• Aesthetic Appeal

UPVC gives you a wide range of foil colours that’ll fit your home perfectly well while also enhancing it’s visual appeal. You can actually get a porch that looks exactly like it’s manufactured from timber frames. To achieve this, all you need to do would be to make use of a wood grain surface finish. This is also long lasting, strong and resistant to fade.

• Little Maintenance

This is a very common feature of uPVC that makes it even more advantageous when used in making a porch. Unlike timber or wood which swells due to absorption of water or shrinks, you’ll never need to worry about all these distortions and more with uPVC. No painting, no sanding and ultimately, low maintenance required.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.