Porch in Chipping Campden

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

No matter how big or small a building is, it can only be as good as it’s foundation - and that’s a fact! It all starts from the footing and when it isn’t deep enough, unlike badly installed gutters or gapped hardwood flooring, can make the whole building collapse to the ground. Just like any code recommendations, the depth of the footings of your porch is a parameter that must be complied with and adjusted to suit your local code requirements.

As a rule of thumb, you should always dig below the frost line when excavating your footings. At this depth level, the moisture present in the soil will be frozen. Ultimately, this will help the ground to act as a barrier to insulate the soil below the footing from freezing during the cold months. As a result, in regions where the weather is almost always very cold the depth of your footings is expected to be at least 48 inches. But in areas featuring a warm climate, you may be allowed to install your footings on grade.

In addition, it’s compulsory that your footings must be installed at a minimum depth of 12 inches below unsettled soil. However, if you’re constructing the structure into a steep hill’s side or by the side of a retaining wall, it’s required that you maintain the least distance to grade both vertically and laterally. In the event whereby you need to achieve a good lateral barrier, you’ll need to have your foundation dug a lot deeper compared to if it’s on a flat surface. For a more accurate and updated information, you can consult your local building inspection department to get familiar with the requirements in your area.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Are you interested in constructing a porch to your property? Estimating the cost of the project before proceeding will solve a lot of possible headaches in the future.

A porch is great place where you can keep your shoes, jackets, dog leads as well as other items to create free space within the property. Apart from this, a porch also serves numerous other purposes to make it a very good structure to have on your property. Not only is it a good means to put a roof over your head when it’s pouring with rain, but also a highly economical way to add floor space to your home. The question, however, how much would it cost to build a porch?

The price of building a porch is based on a wide variety of factors such as the type of materials required, the size of the porch, location of the structure and lots more. As a result, you should note that this guide provide figures that are only a rough guide that’ll put you on the right direction to make informed decisions.

Depending on the type of porch you choose to build, the average cost range from £1,900 to £2,100 for a uPVC porch and up to £10,000 for a lean to porch. There are other types of porch including the traditional porches ( Edwardian and Victorian porches) costing within a range of £2,500 to £8,400.

The materials required also has a great influence in determining the price of a porch. An aluminium porch will cost between £7,5000 to £8,200, while a brick porch will cost slightly less between the range of £2,000 to £8,000. They can both be constructed either as a front porch or as a rear porch, but due to fewer restrictions on aluminium porch, it can be made a lot larger.