Stud Wall/Plasterboarding in Kirkby-in-furness

Find Stud Wall/Plasterboarding Prices in Kirkby-in-furness

Home > Plastering & Ceilings Projects > Plasterboard dry lining > Kirkby-in-furness

Stud Wall/Plasterboarding in Kirkby-in-furness

Internal or partition walls can be moved or knocked through in your property, which can modify the room design and create a more substantial open plan room design for a spacious living area or a kitchen diner. When relocating or knocking through internal walls, it is vital to understand both the sort of internal wall that it is, and whether or not it's a load bearing wall. Internal walls might be brick or block partitions, timber stud partitions, or even prefabricated wall panels. There are no shortcuts when it comes to deciding whether a wall is load bearing or not, it is advisable to engage the services of a structural engineer if you are not sure or cannot view original plans for your premises. Load bearing walls can be relocated, but this is typically more costly and involves constructing additional load bearing solution, for example steel lintels. Moving or knocking through internal walls will typically entail demolition of the pre-existing wall, reconstructing or restoring the new walls, replastering and moving electrics. It could also demand changes to the floor, as occasionally the floors between rooms aren't entirely level, and knocking through interior walls can expose this. Generally moving interior walls won't require planning permission, but you will need to comply with building regulations for insulation and sound proofing. Consulting a structural engineer will ensure that any internal wall changes that you plan on doing will keep your home structurally sound.

Average Plasterboard dry lining cost in Kirkby-in-furness

The average cost of Plasterboard dry lining is £850. Costs vary based upon the materials and the tradesman hired. The upper price range can be as high as £977.5. The material costs are in most cases around £212.5

Average price per Plasterboard dry lining job in 2024

Avg. price low

Avg. price low
£638

Avg. price

Avg. price
£850

Avg. price high

Avg. price high
£978

£1100

£825

£550

£275

£0

Prices based on actual Plasterboard dry lining costs for Kirkby-in-furness, as reported by local LeadsDoWork members.

Plasterboard dry lining installation cost in Kirkby-in-furness 2024

Labour cost £595
Material cost £213
Waste removal £43
Time frame: 1-2 days

Plasterboard dry lining searches in November 2024

Plasterboard dry lining Projects in Kirkby-in-furness in October 2024

88

Requests for quotations in Kirkby-in-furness in October 2024

0

Requests for Plasterboard dry lining quotations in Kirkby-in-furness in October 2024. 0% change from September 2024.

0

Requests for Plasterboard dry lining quotations in Cumbria in October 2024. 0% change from September 2024.

Source: Numbers calculated based on the search volumes in major search engines

Plasterboard dry lining searches in cities and towns near Kirkby-in-furness October 2024

Kirkby-in-furness

Kirkby-in-Furness is a village in the Furness location of Cumbria, England. It is about 5 kilometres south of Broughton in Furness as well as 8 km northwest of Ulverston. It is just one of the largest towns on the peninsula's north-western coastline, watching out over the Duddon tidewater and also the mountains of the Lake District. Kirkby is a load of six various communities, namely: Soutergate, Wall End, Beck Side, Sand Side, Marshside as well as Chapels. The name Kirkby was made use of by the Furness Railway business throughout the building of its Cumbrian Coast Line, as well as was the name they provided to the station which offers these hamlets. The name Kirkby is much older. The church of Kirkby Ireleth, a name of Norse origin, is provided in the Domesday Book as one of the territories forming the Manor of Hougun which was held by Tostig Godwinson, Earl of Northumbria. Much of the housing and also framework in Kirkby emerged because of the growth and also growth of the Burlington Slate Quarries, which are owned by the Cavendish household of Holker Hall and also Chatsworth House in Derbyshire. Residences at Marshside and also Incline Foot were initially built for quarry employees, and also the train linked to the quarries complying with bogie lines. Present-day Kirkby-in-Furness is currently mainly a traveler village yet still provides a work force for the slate and also agricultural work. The neighboring Kirkby Moor rises to 334 m (1098 feet) over water level which includes a 12 turbine wind farm. The town has an increasingly aged population due to the increase in house rates and lack of residences appropriate for first time buyers. This has brought about young households leaving Kirkby, buying cheaper homes in bordering communities and also towns. Therefore, the intake for the local primary school has dropped substantially in the last couple of years, and remains to drop.

Looking for Plasterboard dry lining in Kirkby-in-furness?

Get free quotes from local builders

Get free quotes

How it works

Tell us about your Plasterboard dry lining project

Answer a few quick questions, so we can match you with professionals who can help.

Find up to 4 Builders in Kirkby-in-furness

Get free, no-obligation quotes from 4 verified Builders working in Kirkby-in-furness.

Hire with confidence

Compare customer reviews, services and prices, and choose the right professional for you.

Our reviews

Average

Would highly recommend

Would highly recommend, they found me a firm which I was happy with a quote they give me and went ahead and had my job done within 2 days of enquiring.

Good easy way to find a selection of…

Good easy way to find a selection of trades you need all in one place.

Love LeadsDoWork it's a big part of my …

Love LeadsDoWork it's a big part of my Business I would recommend to anyone

FAQs

How to plasterboard a wall?

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

How to plasterboard a brick wall?

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

How to fit plasterboard?

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

How to cut plasterboard?

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Placholder Image

Other Top Projects in Kirkby-in-furness

Are you a builder in Kirkby-in-furness?

We can help you get more Plasterboard dry lining work and boost your business.

Join today