Oil Boiler (Repairs or Servicing) in Wellington

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How To Make Oil Boiler More Efficient?

During the winter months when the nights get darker and colder, it’s more likely your oil gets used up a lot more quickly. This can be very worrisome as it implies having to spend more money to refill. So what exactly can be done to make your oil boiler more efficient and save you some money?

• Regular Servicing Of Your Oil Boiler

Getting your boiler serviced by a manufacturer approved engineer on an annual basis is one of the easiest and quickest ways to ensure that your oil boiler is operating at its maximum efficiency level. When a full servicing is provided for your oil boiler, checks are made to ensure that all components are functioning the way they should while also identifying the bad or worn parts that may be hindering your oil boiler from functioning in an effective manner. As a result, it helps you see to the fact that your boiler is not consuming more than necessary to make sure your oil boiler lasts longer.

• Set Your Thermostats Correctly

When you set your room thermostats and thermostatic radiator valves (TRVs) the right way, you’ll be sure to get a comfortable home without having to make use of much fuel.

• Consider Smart Technology

If you decide to make use of smart technology like Nest or Hive, you can save more money when compared to their more conventional counterparts. These smart technologies incorporate highly advance intelligent systems to get more familiar with your lifestyle, habits as well as heating operations in order to ensure optimum efficiency at all times.

• Put Your Radiators To Good Use

Try as much as possible to avoid some oversights that can make your radiators consume more energy than required. Consequently, you have to keep them clean, give them space and also take care with curtains.

How Long Does It Take To Service An Oil Boiler?

Are you about to service your oil boiler and wondering just how long it would take to completion? Well, you should first know that during an oil boiler service, there are a wide range of things that needs to be checked. As a result, the service can actually take some time and even more, depending on the present condition of your oil boiler.

During a boiler service, your qualified heating engineer will carry out the following tasks:

• Detach and clean both the burner and fan.

• Examine the combustion chamber rope seal.

• Wipe clean and descale baffles.

• Wipe clean and descale the main heat exchanger

• Detach, clean and replace turbulators

• Examine the combustion levels after cleaning.

He’ll also perform some tank and system checks which includes:

• Inspecting and cleaning condensate

• Testing the fire valve

• Cleaning or replacing the filter

• Cleaning the condense trap

• Conducting a thorough inspection of the tank and oil supply pipe to identify possible damages, deterioration as well as debris.

• Pressure testing the oil supply pipe at the point where it goes underground.

• Examining the system pressure.

With all the aforementioned activities and more, an oil boiler service may take relatively longer period of time when compared to it’s counterpart - gas boiler. This is mainly due to the fact that the boiler itself requires a thorough inspection as well as the oil tank where the fuel is being stored. You get your gas through the mains supply, however oil must firstly be stored inside the tank then filled up when it’s almost low. The oil tank will be inspected to identify possible leaks, bulging, corrosion as well as water.

So generally, an oil boiler service should take between the range of 1 to 2 hours to be completed.

How Can I Get My Oil Boiler Repaired?

Did your oil boiler just broke down and you’re considering your repair options? Well, you’ve come to the right place! Whenever your oil boiler breaks down, you have two options - repair it yourself or get in touch with a reliable professional. If you lack proper training or experience when it comes to fixing of oil boilers, we’d recommend that you rather hire the services of a trustworthy oil boiler engineer who can guarantee the best results while also saving you time and money that could result from possible costly errors.

However the issue is, not all oil boiler repair services are created equal. The words “expert and “professional are now so cheap that almost, if not all oil boiler repair companies online today make use of those words to qualify themselves. However, when several of them are done delivering their oil boiler repair services you’ll have no other choice than to start questioning their claimed status. In order to separate the boys from the men very early on, a little caution and some research is all that’s needed to know the most reliable company to approach.

To get a good repair company, the first step would be to make sure the company is fully accredited with a professional certification scheme so as to be sure that they’re actually qualified to deliver the service.

Another step you can take is by requesting personal recommendations from family and friends. For a company to be referred by several homeowners in the local area then it must be doing something that’s worth the money invested.

You can as well make use of the internet to get a reliable oil boiler repair company. You can start by visiting the website of the company that manufactured you appliance to identify any recommended repair companies. Go through the companies’ testimonials but do not rely too much on them because in several cases they may not be authentic.