Oil Boiler (Repairs or Servicing) in Cleator Moor

How Much Oil Does A Boiler Use?

Are you also interested in knowing the quantity of oil that a boiler consumes to heat up and keep a house warm? Well, you’ll find the answer here. There are so many influencing factors that determines the quantity of oil that’ll be used by a boiler. These factors include the number of hours they’re subjected to use on a daily basis, the boiler’s size as well as how efficient it is. Another factor is how you use your boiler, whether it’s only to provide heating or to provide both heating and hot water will as influence the quantity of oil your boiler uses. As a result, it’s almost impossible to provide an accurate estimate of the amount of oil that an appliance would require to keep running effectively.

In general, to provide a rough estimate, a mid sized oil boiler appliance could make use of up to 3.5 litres of oil per hour when full, but if it’s a large appliance, then it can burn up to 4 litres of oil per hour. However, it should be noted that this is only when the boiler is operating flat out. In the event whereby the water inside the heating system is already hot and the boiler is only working to maintain the level of warmth, much less quantity of oil will be used. And as expected, there will also be times in which your boiler will not be on, and therefore no oil or fuel will b used.

Your home’s size as well as how properly insulated it is can also be a significant influencing factor here. As you would have guess a big home and/or poorly insulated will use up more oil because it’ll be harder to heat up or keep warm. Overall, for some households, 1000 litres of oil will be sufficient to get them through the year, whereas the same quantity may not be enough to get other households through just the winter months.

How Long Does It Take To Service An Oil Boiler?

Are you about to service your oil boiler and wondering just how long it would take to completion? Well, you should first know that during an oil boiler service, there are a wide range of things that needs to be checked. As a result, the service can actually take some time and even more, depending on the present condition of your oil boiler.

During a boiler service, your qualified heating engineer will carry out the following tasks:

• Detach and clean both the burner and fan.

• Examine the combustion chamber rope seal.

• Wipe clean and descale baffles.

• Wipe clean and descale the main heat exchanger

• Detach, clean and replace turbulators

• Examine the combustion levels after cleaning.

He’ll also perform some tank and system checks which includes:

• Inspecting and cleaning condensate

• Testing the fire valve

• Cleaning or replacing the filter

• Cleaning the condense trap

• Conducting a thorough inspection of the tank and oil supply pipe to identify possible damages, deterioration as well as debris.

• Pressure testing the oil supply pipe at the point where it goes underground.

• Examining the system pressure.

With all the aforementioned activities and more, an oil boiler service may take relatively longer period of time when compared to it’s counterpart - gas boiler. This is mainly due to the fact that the boiler itself requires a thorough inspection as well as the oil tank where the fuel is being stored. You get your gas through the mains supply, however oil must firstly be stored inside the tank then filled up when it’s almost low. The oil tank will be inspected to identify possible leaks, bulging, corrosion as well as water.

So generally, an oil boiler service should take between the range of 1 to 2 hours to be completed.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.