House Rewiring in Peacehaven

For most homeowners, rewiring a house is always a sore subject they’d prefer to avoid especially when they think of the expenses they’d have to incur or the mess and complexity that the project involves. However, this is a subject we’d all have to face sooner or later as an old wiring poses a lot of drawbacks, while an improper wiring can also prove to be more expensive and even cause more damage as it can lead to not only electrical shorts but also electrical fires. When a wire triggers a spark or a current overload, this can cause fire and the entire house may be down in ashes within a couple of minutes. Hence, one of the several reasons why house rewiring is just too important to ignore.

In this FAQ, we’re going to take you through the house rewiring process so as to ensure that your project is done to perfection. However, if you do not feel confident enough to pull this off, we’d strongly recommend you get in touch with a reliable electrical professional who can guarantee that a safe and effective work is done.

• Firstly, you’d have to upgrade the main service panel to a minimum of 100 amps
• Fit dedicated circuits in the service panel for all the home’s major appliances.
• Allow for a space of about 6 to 8 feet between electrical outlets throughout the house in order to cut out the need to run extension cords which could be a fire hazard.
• Install only three-prong type to avoid electrical shocks when fitting new outlets.
• Using ground fault circuit interrupters, fit outlets in the bathrooms, kitchen as well as outdoors. These outlets will shut themselves out so as to prevent electrical shock when wet.

There is no set guidelines for rewiring your property however if your house is more than 20-30 years of ages it would certainly constantly be best to get an EICR accomplished to determine the problem of the electrical installation. If you are most likely to be accomplishing a great deal of repair works such as a brand-new kitchen/bathroom/extension this might additionally be a good time to have your house rewired as every little thing might then be done simultaneously

Modern wires is PVC covered, PVC shielded and copper is made use of for the conductors. It lasts for years. At once in the 1940s and 1950s cables were made using rubber as well as this wires was known to be harmful. Rubber protected as well as sheathed cable came to be dry and also weak, especially if it obtained very warm under hefty use, and also the threat was the dry as well as breakable rubber made use of to break away from the conductors leaving revealed live wire. This caused fires and also fatal shocks if touched. Modern PVC electrical wiring does not struggle with destruction this way so the requirement to rewire is somewhat lowered.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Unlike in houses constructed in the 1960s, where you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type, majority of houses built in the 1970s would not need to be rewired. Most often than not, what they’ll need is just a consumer unit as well as an earthing upgrade. If you happen to have a consumer unit change, the electrical professional you hire would have to inspect the most parts of the property regardless. With that answered, you may also wish to know just how often a house would need to be rewired.

First and foremost, in order to make sure that your wiring is safe there’s a need to ensure that a periodic inspection is carried out by a fully licensed and qualified electrician every 10 years. Meanwhile for rental properties with tenants, the landlord is required to carry out a periodic inspection at least every 5 years. This will make sure that the electrical works in the property are safe, up to date and suitable for continued usage.

In order to determine whether your house needs to be rewired, there are some signs or indicators you’d have to watch out for. If you notice one or even a combination of the following , then you should get in touch with a registered electrician:

• Discoloured outlets and switches
• Persistent burning smell
• Outlets problems
• Flickering lights
• Tripping circuit breaker or blown fuses
• If you happen to possess aluminium wiring
• If you have continually experienced electrical shocks

It must, however, be said that rewiring a house is a messy and quite disruptive work. It’s also considered to be quite dangerous and recommended to be carried out only by a professional is well trained and experienced when it comes to tackling electrical works.