House Rewiring in North Walsham

For most homeowners, rewiring a house is always a sore subject they’d prefer to avoid especially when they think of the expenses they’d have to incur or the mess and complexity that the project involves. However, this is a subject we’d all have to face sooner or later as an old wiring poses a lot of drawbacks, while an improper wiring can also prove to be more expensive and even cause more damage as it can lead to not only electrical shorts but also electrical fires. When a wire triggers a spark or a current overload, this can cause fire and the entire house may be down in ashes within a couple of minutes. Hence, one of the several reasons why house rewiring is just too important to ignore.

In this FAQ, we’re going to take you through the house rewiring process so as to ensure that your project is done to perfection. However, if you do not feel confident enough to pull this off, we’d strongly recommend you get in touch with a reliable electrical professional who can guarantee that a safe and effective work is done.

• Firstly, you’d have to upgrade the main service panel to a minimum of 100 amps
• Fit dedicated circuits in the service panel for all the home’s major appliances.
• Allow for a space of about 6 to 8 feet between electrical outlets throughout the house in order to cut out the need to run extension cords which could be a fire hazard.
• Install only three-prong type to avoid electrical shocks when fitting new outlets.
• Using ground fault circuit interrupters, fit outlets in the bathrooms, kitchen as well as outdoors. These outlets will shut themselves out so as to prevent electrical shock when wet.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

When the wiring on your property becomes dated, dangerous or non functional, then rewiring of your house becomes a necessity. If you’re thinking about rewiring your house, one of the first few things you’d have to put into consideration is the cost of completing the project in order to help you set a budget and start to plan. In this post, we seek to provide you with the most accurate cost possible for your project to help you get started as soon as possible.

In general, the average cost to rewire a house can vary from £2000 to about £10,000, which includes the prices for both material and labour. Factors that can have a great influence on the final price includes the type of your property, the quality of the existing wiring as well as the complexity of the installation needed. The most important determinants are probably the type of rewiring task you go for (whether for the whole house or some specific parts ) as well as the size of the house. The qualification of the electrician hired and the labour costs will also influence the final budget required to a great extent. Overall, the average cost of rewiring a house stands at £4000 and it will usually take up to 7 days for a complete rewire to be done. For older properties, you may need completely rewire the property in order to enhance the energy efficiency. However, this may not be required the your home was just recently built.

Being a messy and disruptive task which can also be very dangerous especially when handled by a inexperienced individual, we’d strongly recommend that house rewiring is carried out by a qualified and registered electrician who is well trained to perform this task to perfection.

When it comes to electrical works, safety is always paramount. Although a complete house rewiring service may seem quite expensive, when compared to the safety it provides, you’d realize it’s well worth it. We know all too well that human nature tends to prevail to overlook small electrical issues until it’s too late or probably gets out of hands. When this happens, not only will you have to spend more to get the issue resolved, but it may also lead to some damages to your property. Hence, the need to identify and resolve electrical deficiencies as soon as possible. In this post, we’ve compiled a shortlist of some of the top signs that your house needs rewiring. Let’s take a look!

• Dimming or flickering lights. This is one of the most common signs that your house needs to be rewired. When a light brightens, it means there’s too much voltage and when it dims, it implies it’s receiving too little voltage. You may be tempted to think this is a lighbulb issue, but this type of decline in power is usually as a result of a loose wiring or faulty circuits which should not be ignored.
• Regularly blown fuses. With the steady development in technology as well as electrical appliances within our houses, older style fuses that are not designed to contain this amount of electricity will end up blowing. If your fuse blows on a more regular basis, then there may be a need to upgrade them to more modern circuit breakers.
• Lightbulbs burning out in their sockets. This is usually a sign of bigger issues in your wiring which is often caused by fluctuations in voltage.
• Sparking outlets. These can be perfectly normal, but at times they can also be a clear signal of a potentially dangerous problem which should not be ignored.