Guttering in Mallaig

1. Hang a plumb bob from the outlet to the drain to use as a guide while you draw several marks on the wall with a pencil to show you where the downpipe will run.
2. Join the marks up with a straight edge, creating a line to show where the centre of the downpipe will be.
3. Position a downpipe clip at the top of wall, in the centre of the pencil line. Mark the position of its fixing holes on the wall. If you need an offset bend, put a downpipe clip directly below the bend.
4. Repeat the process down the wall. Make sure there is no more than 1.8 metres between pipe clips.
5. Refer to the guttering manufacturer’s instructions to see which drill bit is required. Use a drill to drill the fixing holes and insert wall plugs.
6. Fit the first piece of downpipe starting from the outlet and moving towards the drain.
7. If you need to add more downpipe, join the two pieces with a pipe socket and clip. Leave a 10mm gap between the end of the pipe and the bottom of the pipe socket, because it will probably expand. Then attach a pipe clip over the joint.
8. Continue attaching pipe clips down the length of the downpipe.
9. If you need to, fit a downpipe show to direct the water into the drain. Attach a downpipe clip directly below the socket of the shoe.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!

A gutter is part of the system that takes rainwater away from a building. Every home will have some form of guttering system to stop water from dripping off the roof and into the walls. It’s important to keep your gutters clear because if water starts to seep into your home’s walls, you’re likely to get damp.

A guttering system consists of half pipes, troughs, bends and downpipes. They’re usually cylindrical in shape but they may be square on some homes and in countries outside of the UK. Technically, the gutter is the part that you’ll see across your roof that collects rainwater. The water will then feed into a downpipe from your roof’s edge to the base of your home, where you can collect it in something like a water butt, or it will be discharged to a surface water drain or soakaway.

In early times, gutters used to be made from lined wood or stone. Lead was often used as the liner to stop rainwater from seeping through the material, but you won’t see it used much anymore. These days, most homes have uPVC guttering as it’s a hardwearing plastic that should last a long time. But you’ll also see gutters made from aluminium, cast iron and copper, especially on period homes or those in a conservation area.

Every home needs a guttering system to ensure that rainwater doesn’t affect the foundations of the property. It’s also important to keep the gutters clear of debris like fallen leaves, as this will cause them to overflow, potentially causing water to soak into the walls and causing damp.