Ground Source Heat Pump in Isle Of Bute

The bigger the ground source heat pump, the better right? Wrong! And you’ll definitely be sorry to make such a huge mistake. When planning to install a heat pump, determining the size of the ground source heat pump is not as direct and straightforward as many homeowners would think. Here, you’ve got only a small margin for error. When the pump is too small, the heat pump will make use of the backup heater too often and in the event whereby the heat pump is too big, it’s going to short cycle. Both situations are preferably avoided as they’ll both leave you with an expensive and inefficient system.

To get the accurate size of a heat pump, there’s usually the need to hire the services of an expert and licensed heat pump installer who possesses a top notch design calculation software. In reality, the majority of inefficient systems are caused by a lack or poor understanding of the suitable design software.

There are many factors that can influence the calculation of a home’s heat pumps size. These includes

✓ Radiators and underfloor heating sizes

✓ Insulation, property fabric as well as heat loss

✓ The number of rooms in the property

✓ The types of rooms and their uses.

✓ The desired indoor temperature for varying rooms

✓ Seasonal temperature fluctuations.

Generally, a bigger house will require a bigger ground source heat pump. With an eye on the age of the property, heat loss as well as the types of the rooms, a house of about 100 square metre can require up to 4kW ground source heat pump. And for a house that’s about 200 square metre, the ground source heat pump also doubles to 8kW.

Are you interested in fitting a ground source heat hump in your home? If yes, then one of the thing you’d probably like to know is whether or not the heat pump is noisy. In this article, we seek to provide you with necessary information that’ll solve these mystery.

One thing you should when it comes to heating products is that they all make some noise. However, they’re usually a lot quieter when compared to fossil fuel heating systems. Generally, a ground source heat pump can reach within the range of 40 to 60 decibels depending on the manufacturer of the product as well as it’s installation.

The noise levels of heat pumps are a major concern for several homeowners. However, the fact is when the system becomes a nuisance or becomes noisy, that is always a sign of poor planning as well as poor quality installation. This is because heat pumps, in general, are not usually noisy.

In ground source heat pumps, volume isn’t quite associated due to the lack of a fan unit. However, it remains a very common question for homeowners who intends to install a ground source heat pump to ask whether or not the type of heat pump is noisy. Just like any other heating product, there are components in the ground source heat pump that produces some noise but this is always not as much as that of an air source heat pump. This is due to the fact that the heat coming from the ground is more consistent, hence the compressor’s power capacity wouldn’t be as high. What’s more? This type of heat pump doesn’t also work at full throttle which also plays a key role in its low noise level.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.