Ground Source Heat Pump in Hyde

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

First and foremost let’s look at the meaning of a ground source heat pump. A ground source heat pump is simply a renewable heating system which happens to absorb the low temperature solar energy stored in the ground or in water with the help of a pipework that’s submerged and converts this energy into a higher temperature through compression. A ground source heating pump is capable of supplying the entire heating and hot water needs of a building throughout a whole year regardless of the season. So how exactly does a ground source heat pump work? Let’s have a look!

In principle, a ground source heating pump makes use of a refrigeration system but in a reverse form as it extracts low temperature heat from one point or location which is the source and transfer a higher temperature heat to another point or location - the sink. The pumps are powered by electricity and the operational principle can also be incorporated at generating both heating and cooling energy.

Knowing fully well heat naturally flows from warmer to cooler places, the ground source heat pump takes advantage of this physics by distributing a cold fluid via ground array pipework either in the ground or in water. It’s able to extract low grade energy from external sources of heat which includes soil, rock, lakes as well as streams.

Once the absorbed energy has been released to the heat pump from the ground or water, the fluid proceeds with its circuit back to the pipework to start its cycle all over again. Some of the benefits of the ground source heat pumps includes low carbon emission and improved air quality, efficient and affordable heating, the use of free heat from the ground and lots more.