Gardening in Tower Hamlets

Garden slabs are a joy to behold but only when done the right way. Well, the installation of paving slabs shouldn’t be exceed digging a little here and there, buying a small amount of mortar and pressing down the garden slab, right? Absolutely not! But we must admit how great it would have been if only it were that easy in real life. Let’s be honest, in reality, laying garden slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. Consequently, this happens to be a stressful and quite tricky challenge. If you lack the required confidence to pull this off, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the garden slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

1. Mix a layer of mortar for each paver.
2. Apply the mixed mortar onto the sub base by using the trowel.
3. Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.
4. Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.
5. Take a measurement of the gap between the pavers
6. Repeat the above steps until all pavers have been perfectly laid
7. Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.
8. Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard-bristled brush.

Chances are at some point you’d probably given a though about how steps would fit in perfectly in your garden, except of course, your yard and garden is flat. Adding steps and gardens makes it a lot easier to get around your yard while also enhancing its curb appeal. In order to avoid the cost of hiring a professional to get the task done, you might be tempted to make it a DIY task. However, if you lack the required skill and confidence to pull this off, we’d strongly recommend you call in a professional so as to avoid costly errors. In this post, we’re going to take you through the garden steps building process. Let’s take a look!

1. Measure the vertical height of the slope by marking it with two parallel lines. Once done, proceed by connecting a string line to the slope’s top and hold it in a horizontal way, take a measurement of the flight’s length and breadth. Divide the measurement by 200mm to get the number of steps that’ll be required. Then proceed to divide the number by the height to identify the depth of each step.
2. Working downwards from the flight’s top, dig the step shapes and also dig a shallow trench and install a concrete foundation.
3. Enable the foundation to harden by leaving it for about 48 hours, then install two courses of bricks on the concrete strip and use gravel to backfill.
4. With the help of a trowel, apply mortar to the top of the brickwork. Place the first slab on the mortar bed and press down. Then, make use of a spirit level to make sure that the steps are level.
5. On the back edge of the first tread, you should proceed to build the second rise, backfill and install the slab to form the second tread – just like the previous step. Repeat this process until you’ve gotten to the top of the flight.

Whether you’re starting a garden from scratch or adding plants to a garden that needs a big of work, the biggest step in planting a garden is preparation. We’ll give you a few tips on how to plant a garden whatever your garden’s size. Check your soil The most important thing to do before you start to plant a garden is check your soil type. Different plants suit different soils, so you should choose ones that will like the soil in your garden. If your soil is sticky and muddy, it’s referred to as clay soil, but if it runs through your fingers when you pick it up it’s known as sandy. Ideally, you want something between the two to help your plants’ roots spread easily. If you have heavy clay soil, you’ll need to add well-rotted manure or compost to improve the structure, but if it’s sandy you’ll need to add organic matter to improve its fertility. Make a plan Don’t just start planting wherever – make sure you’ve got a plan of where you want everything to go. Do a simple drawing or cut out photos from magazines or the internet. How to plant bare root plants and trees When you’re planning what to plant in your garden, make sure you choose the correct amount and size of trees you’re going to plant. In a small to medium garden you only want one or two trees, and you don’t want anything too large that might spread too far. When you’re ready to plant, make sure there’s enough room for the roots to spread. Look for the soil ‘tide mark’ near the base which will show the depth that it was planted before, and use that as your guide. Dig your hole to the correct depth and width and fork the sides so it’s easier for roots to get in. Add some well-rotted manure and place the plant in the hole so the roots are spread out and fill the hole with soil. Planting potted plants Dig a hole deep enough for your plant – put the pot in the hole to check whether you’re there yet. You want around 2cm around the outside and don’t make the hole any deeper than the pot. If your plant has a tight root ball from outgrowing its pot, gently tease out the roots – it won’t harm the plant. How to plant plug plants in your garden Plug plants are usually mail-order plants that you get in spring and are a great way to start planting a garden. You must handle them carefully and water them before planting. Fill a small pot with compost and make a well in the centre, then drop the plug in. Gently pat the soil around it. You might need to pot them again to the next size up later on, and harden them off outside before planting them in the ground after there’s no risk of frost. With these few tips you can easily get started with planting your garden. But if you need some help and advice, get in touch with local gardeners who will be happy to give you a quote.

There are several reasons why you may wish to plant a garden. To have a healthier environment, eat healthier, cook with fresh produce and lots more. Regardless of your purpose, one challenge faced by several home and property owners is exactly how to go about this and where to get started. If you’re having the same issues, then you’ve come to the right place. In this post, we’re going to take you through the process involved in planting a garden to ensure your project turns out a success. If you lack the confidence required to pull this off, we’d highly recommend you call in a professional who can guarantee the best results.

1. Start small. Being overly ambitious when planting a garden could be easiest way to a disastrous outcome. Give yourself a realistic goal and learn to plant healthy and productive plants by starting small.
2. Identify your site. To ensure a great garden, the plants need lots of sunlight. So, you can go for a space that gets about 6 to 8 hours of sunlight on a daily basis. Also, make sure that there’s a water source nearby to make it easy to give your plants water as required.
3. Choose you garden type. Decide how your garden will grow, be it in raised beds, in ground, in containers or a combination of styles. This will ensure that your garden is neat and orderly while also enhancing its curb appeal.
4. Make a list. Create a list of the plants you’d love to have in your garden.
5. Plan your planting. This involves spacing your plants as they’re going to grow bigger, deciding which plant goes where and identifying the best soil to grow them.
6. Get your plants.
7. Plant them.