Floor Tiles (Supplied and Fitted) in Johnstone

How To Lay Tiles On Concrete

Installation of tiles on concrete sub-floors can be done with relative ease under adequate guidance. Here is what you have to do.

lPrepare The Concrete Subfloor

• Ensure the concrete is dry, clean and must be at least 6 weeks old.

• If there are dips and humps, level the concrete using a levelling compound.

lSet Out

• Working from the centre outwards, take a measurement of the floor (both length and width) and draw a cross at the centre.

• Lay out the tiles from the cross with a space of 3mm between each tiles. This will allow for movement stresses within the floor and later to be filled with grout upon installation of the tiles and adhesive dried.

lCut The Tiles

• Due to the particularly had nature of some floor tiles such as natural stone and porceclain, high quality tools are usually required to produce a clean cut through the tiles. With the help of an electric wet cutter alongside a slide cutter and nippers, your job would be made a lot easier.

• For a better result during intricate cuts, make use of a cardboard template.

lFix The Tiles

• The tiles should be fixed using a cement-based adhesive.

• Ensure to refer to the packaging or product data for the mixing ratios information.

• Stir the mixture till its lump-free

lApply The Mixture

• Spread the mixture onto the concrete sub-floor to create parallel ribs with the help of a floor trowel.

• Push the tiles into the parallel ribs.

• Clear out any excess adhesive from the tiles surface with a damp sponge.

• Do not walk on the tiles for at least 2 hours.

lGrout

• Once the adhesive is dried, wipe out any dust, adhesive or dirt from the tiles’ gaps.

• Mix about 4 to 5 parts of grout powder with 1 part of water and ix together.

• Apply the mixed grout diagonally across the tiles using a soft rubber grout float.

• Wipe out excess grout from the tiles surface and allow the tiles to dry.

• Stubborn residues can be cleaned using any washing up detergent with warm water within 24 hours after grouting.

Do you wish to have your residential or commercial space tiled? With a plethora of benefits that comes with a tiled floor, it’s little surprise more and more home and property owners are going for this special flooring type. Not only are they able to improve the curb appeal of any property, but they’re also resistant to moisture helping to increase the durability of the house – be it wall or floor tiles.

Tiling a floor is not the simplest of tasks and should be done with utmost care and attention to details. If you lack the confidence to pull this off, we’d recommend you hire a reputable professional who can guarantee the best outcome the first time.  In this guide, you’ll find processes involved in floor tiling to help put you in the right direction.

Floor Tiles Installation Procedures

1. Floor Preparation
   The first step is to prepare the floor by moving all objects like mortar, adhesives and more. Use concrete patching compound to fill ill low spots and cracks, until the floor is levelled.
2. Ensure the floor is dry and clean.
3. Pattern Layout
   Take the measurement of each wall’s length while also taking into account the room’s diagonals.To help place the tiles in an orderly manner, make use of a chalk to mark down lines on the levelled surface in question and ensure it’s parallel to the walls.
4. Adhesive Preparation
   Mix the appropriate amount of water with the adhesive (bonding agent). The mixture should be toothpaste-like thick to ensure the durability of the tiles.
5. Tiles Placement
   Depending on the tile’s size, evenly spread the mortar on the floor using a notched trowel. Lay the first tile on the bonding agent (adhesive or mortar) and apply a gentle and little pressure on the tile.
   
   Repeat the technique for other tiles using plastic spacers to ensure the edges and corners are properly aligned.
6. Tiles Cutting
   Cut the tiles (if necessary) with the help of a wet saw or scoring cutter featuring a diamond-tripped blade.
7. Grout Application
   Filling of the tiles’ gap is done using the grout. It can be applied to the joints with a rubber float. After application, allow the grout to set up for some minutes. Use sponge and a bucket of water to clear out any adhesive leftover.
8. Grout Sealing
   Use a foam brush or applicator bottle for the sealants’ application. Clean out excess sealer within 10 minutes.

How To Remove Tile Floor

Removing old tile can be a very tricky process which require lots of skills and experience to get right, the first time. Here, you’ll learn the best approach to removing your old tile by yourself. During the removal process, be sure to incorporate the necessary tools while also protecting yourself by putting on the recommended safety requirements. These includes a floor scraper, paint scraper, dust mask, handheld chisel, safety glasses, drop sheet as well as leather gloves or top quality riggers.

Tile Removal Process

lBreak The First Tile

• Use a hammer to break the first tile (target the centre of the tile with the hammer).

• To protect yourself from the sharp edges of the broken tile, use a drop sheet to cover the surfaces.

lRemove The First Tile

• With a chisel, remove the broken tile that’s still bonded on the floor.

• Position the chisel on the grout line at the tile’s edge to remove the broken but glued tile.

lBreak Up The Remaining Tiles

• Break up several tiles at once and use the floor scrapper to remove it.

• Ensure that the bonding agent used is pliable to make the job a soft work. If the bonding agent is a bit more permanent in nature, then you might want to consider a dynamite to dislodge the flooring.

lRemove The Mortar

• Hit the mortar with a hammer on a 2 to 3 foot square section to remove it from the underlayment.

• Scrape off the mortar’s broken pieces using a floor scraper

• In the event whereby most of the mortar is not removed, your best bet would be to change the underlayment.

• Bonding agent (adhesive) removal is not the easiest of tasks. To make it a bit simpler, you can softening the adhesive with a heat gun before scraping with the help a wide putty knife.

Tile removal is not only a tedious task, but can also be harmful if adequate care is not taken. If you’re inexperienced or not well trained, we’d recommend you hire the services of a professional to avoid making mistakes and incurring extra costs.

Can You Use Floor Tiles On Walls?

Some floor tiles are so lovely you just can’t help but wonder if its safe to be used on the walls as well. If you’re also thinking along the same line, you’re not alone! Several other home and property owners are busy finding answers to this particular question. Now let’s look at the possibilities.

Generally, any tile designed as a floor tile by the tile manufacturer can also be laid on the wall (vertical surfaces) as well as countertops. Due to the fact that the floors are usually subjected to greater use than the walls in terms of foot traffic, the durability required is also considerably greater. Therefore, a floor tile with Abrasion Resistance values ranging from I - V is suitable for wall installation. However, you should take note that exterior wall applications must be different from its interior counterparts and must only be incorporated on tiles that are frost resistant.

There are two other factors that must be taken into consideration before you install a floor tile on your walls which includes the weight of your tiles per m2 as well as the strength of the surface in which the tile is to be installed. If you don’t want your tiles falling off, the combined weight of the tiles with the adhesive and grout should not be more than the maximum weight required per m2 (20kg to 35kg depending on the wall substrates).

Now that you have an idea of the possibilities of installing floor tiles on walls, it must, however, be said that reverse is the case when it comes to installing walls tiles on the floor. Wall tiles are, generally, not suitable to be laid on the floor as they are mostly non-vitreous ( can not withstand excessive impact, abrasion or thaw cycling).