Floor Tiling in Larkhall

Kitchen floor tiles are a very popular choice for several reasons. They’re durable, visually appealing, resistant to moisture and stain and also relatively easy to maintain and install especially when compare to wall tiles. This is a task that can be done by any competent DIYer but requires a lot of patience as well as confidence. If you lack these attributes, then we’d recommend that you hire a professional floor tiler who can guarantee the best results the first time. In this article we’ll take you through the kitchen floor tiling process. Let’s get started!

• Prepare The Subfloor

✓ Ensure the subfloor is very secure to support both the tile and the people working across it.

✓ If necessary, you can strengthen the kitchen floor with the help of a vinyl, heavy felt or any other good backer board.

✓ After successfully securing the floor, proceed to clear out all dust and dirt.

• Mix The Mortar

✓ Mix a thinset mortar be referring to the instructions on the package. ( Mix only the quantity you can apply within 30 minutes).

✓ Once the mixture looks similar to the thickness of mayonnaise, allow it to rest for about 10 minutes before application.

• Apply The Mortar

✓ Apply a thin layer of mortar

✓ Do not cover extensive areas as the mortar can become very dry.

✓ Spread the mortar with a trowel in curved patterns to make it flat on the floor.

• Set The Tile

✓ Set down the tile slowly, apply a little pressure until its holds firmly to the surface. ( Apply a consistent amount of pressure throughout to ensure equal heights for all the tiles)

✓ Continue with the process until all full tiles are well positioned

• Cut The Tiles

✓ Once all the full tile pieces are in place, start cutting to cover the edges requiring smaller tile pieces.

✓ Take accurate measurements of the outer edges needing smaller tile pieces.

✓ Cut the tile pieces to fit the measurement taken with the help of a wet saw or hand tile cutter.

• Grouting

✓ Remove all spacers and mortar residues and lay the grout

✓ Apply the grout along the tiles’ seams with a grout float

✓ Clean out excess grout with a damp sponge after leaving it to dry for about 30 minutes

✓ Once the grout is fully dried, apply the sealer (the drying process normally takes within 3 to 4 days).

Due to the plethora of benefits ceramic floor tiles are able to provide, there’s little surprise they’re a popular flooring choice amongst homeowners. Not only are they durable and good looking, but they’re also resistant to both moisture and stains. Hence, they’re very easy to maintain and with skill, confidence and patience, can also be relatively easy to install especially when compared to wall tiles which is a vertical surface.

If you’re looking to install ceramic floor tiles by yourself, you’ve come to the right place. This is a task any confident and patient DIYer should be able to do with ease. However if you’re not confident enough to pull this off, it’s advisable to get a professional for help. In this guide, we’ll walk you through the process of fitting ceramic floor tiles.

✓ Prepare the subfloor. This involves making sure the layout is even from side to side on both directions, picking up loose tiles and setting them aside.

✓ Spread a thin set of mortar over a 3x3 foot section at the intersection of the layout lines using a notched trowel.

✓ Start to lay the tiles from the centre point of the two layout lines. Simply set the individual tile into the mortar and tap gently with a rubber mallet. Ensure to use spacers at the corner of each tile to maintain an even grout line between the tiles.

✓ Continue spreading the mortar and complete laying of the tiles

✓ Once all the tiles have been perfectly fitted in the mortar, proceed to mix the grout according to the manufacturer’s instructions and apply it with the use of a rubber grout float.

✓ Wipe clear any excess grout with a grout sponge. Once done, let the grout dry up a bit, then remove the haze that comes up.

Have you laid your tile and left it to set? If yes, then the next step is to start grouting. Before you get started there’s a need to make ready the right grout for the type of your grout as well as background material. If you’re not certain of the right grout you can reach out to the grout manufacturer for help. Grouting of floor tiles is not the easiest and tasks and should be left to a reputable professional in order to avoid costly mistakes and unnecessary costs. In this post, we’re going to take you through the processes involved in grouting of floor tiles in order to put you on the right track. Let’s take a look!

1. Depending on the adhesive used to lay your tiles, make sure you leave enough time for the tiles to fully set.
2. Get a mixing bucket and mix grout powder and water as instructed on the packaging. Ensure not to make too much as this will make it solidify quickly and unstable.
3. Apply some grout on the tiles - hold the grout float at 45 degree angle and apply the grout to fill all of the joints.
4. Once you’re done grouting all of the joints between the tiles, leave it for up to 10 to 15 minutes to dry before wiping down the tile surface using a damp sponge. Ensure not to apply too much pressure on the grout joints.
5. Let the tiles rest for about an hour so as to allow the grout solidify and harden a bit more. Once done, proceed to take off the excess grout and smooth it off.
6. Wipe down the tiles until they’re totally clean using a clean cloth.

If you’re considering the installation of large format porcelain tiles in your home or property, you’d probably want to know how you can go about the laying process. Large porcelain tiles can measure up to 3m in length and as a result, requires specialist skills, equipment as well as products in order to see to a high quality installation of the tiles. In this guide, we share with you expert tips that’ll help install large porcelain tiles onto floor space with relative ease. Let’s take a look!

✓ Prepare the tiles. This includes cleaning the surface of the tile of any dirt, dust and removing any temporary protective layers. This is because any contamination to the tile’s surface can affect the suction action of the lifting frame.

✓ Cut your porcelain tiles. For cutting, the tiles should be transferred to a stable base for for more accuracy and clean cut. Use the measurements to get a perfect cut and if you’ll require a straight cut simply use the score and snap tools and techniques.

✓ Prepare the adhesive. Follow the manufacturer’s instructions to prepare the adhesive.

✓ Install the large porcelain tiles. Use a 4mm notched trowel to backcomb the adhesive onto the tile’s reverse. All ribs should run in same direction and also be parallel with the shortest length. Use a larger notched trowel to apply the adhesive to the substrate. Once you’ve applied the adhesive to both surfaces, you can then life the tiles into place with the lifting frame. Then use the tile levelers to ensure the tiles are flush at the joints and wipe off any excess adhesive

✓ Apply the grout.