Boiler Grants in Roy Bridge

A combination boiler, also referred to as a “combi boiler, delivers both domestic hot water and space heating in a single package so as to save space, and in a lot of cases, money. These great features makes the appliance a very popular choice in UK homes and in fact, it represents more than 50 percent of all new boilers fitted in the UK on a yearly basis.

Most modern and high efficiency combi boilers are usually stainless steel condensing boilers which normally features an in-built secondary heat exchanger to deliver domestic hot water to a home or property. What’s more? When it comes to the heating season or the cold months, the combi boiler will operated as required to heat a structure and offer hot water for showers, sinks as well as other hot water appliances around the house. And when it gets to the warm season or summer months, the combi boiler will only work when there’s a need for domestic hot water which also helps you save more money.

Combi boilers are able to provide domestic hot water in such a way that’s energy efficient due to two primary reasons - the combi units possess a very high operating efficiency and also have a low internal water volume. As a result, in during the hot summer when space heating is not required, you’ll only have to pay to heat up the hot water that you really need and not an entire tank.

Combi boilers also have the following benefits:

✓ Lower costs. Due to the combined nature of the boiler and the lack of tank in the roof space, the installation time and costs are at a minimum.

✓ Saves space in your home as it effectively combines a central heating boiler with a water heater into one unit.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

A boiler is simply the most important part of a central heating system as it generates the heat that warms up the home or property. Basically, the appliance or small furnace makes use of gas, LPG or oil in order to fuel its operation. However in the UK, most boilers are usually fuelled by natural gas which is supplied automatically from the national gas grid. And depending on how it operates, there are various types of boilers.

Typically, a gas central heating boiler will have multiple pipes entering from underneath. While one pipe supplies the boiler with gas from the mains gas supply, another pipe allows cold water to enter the boiler to be heated, the last pipe then enables hot water to exit the boiler so it can be distributed around the home.

✓ There are fuel jets and heat exchangers inside the boiler. When the heating is turned on, a valve is opened to allow the mains supply gas to enter a sealed combustion chamber in the boiler. There are multiple little valves which permit the entry of the gas before being ignited by an electric ignition switch. These jets heat a metal component in the boiler known as a heat exchanger which works to transfer the heat to the cold water pipe and heat up the water.

✓ Once the water has been heated to the target temperature, it’s then pumped through a circuit of pipe which runs around your home by an electric pump.

✓ The heated water enter each radiator, is then transmitted via a closed loop and radiates heat into each room.

✓ Once done travelling through all radiators, the water then returns to the boiler at which it must have been cooled. Therefore, the boiler will have to reheat following the same process before circulating. The water can only be drained by a professional Gas Safe engineer

If you’re thinking about getting a new gas boiler for your home or property, then you might also be wondering how much it’ll cost you so you can set a budget and start planning. As simple as this question sounds, it’s actually very tricky to provide a simple and short answer as the costs of installing a new gas boiler alone varies greatly based on the parts needed, the amount of work required, your location, their availability as well as the company you hire for the project.

When it comes to purchasing a new gas boiler the price you’re expected to pay also depends on multiple influencing factors such as the type, brand as well as your most preferred gas boiler model. However, one thing you should have in mind is the fact that your gas boiler is right at the heart of your home or property and can be a complicated piece of machinery. As a result, you wouldn’t expect gas boilers to come cheap. Generally, it’s going to cost within the range of £500 to about £2,500 to get a new gas boiler. Therefore, it’s always advisable to obtain all necessary details and facts before you decide to purchase a replacement gas boiler.

This price range may seem too high as it’s usually a turn off for most homeowners. However, it’s worth noting that gas boiler replacement costs and gas boiler installation costs are, more often than not, compensated by the saving you’ll make off your utility bills - all thanks to the new and more energy efficient boiler you just installed in your home. And even more importantly, when it has been estimated that roughly half of the amount spent on energy on an annual basis depends on your boiler.