Pattern Imprinted Driveway in Billingham

• Where you live
• How big you want your driveway to be
• What colour or design you would like
• Whether any additional work will need to be completed to prepare the area for the driveway

Paving comes in a wide range of colours and patterns. Consider using a contrasting colour for the edges of your patio or driveway for a tidy effect. A paving specialist can advise you on different combinations possible, alternatively, have a look online at what products, shapes and colours are produced.

1. Prepare the sub-baseThe driveway company will excavate, or dig, the existing surface down to a depth of around 200mm. They will remove any debris from the area may place it in a skip or arrange for it to be removed in another way. When they dig down to the sub-base of your previous driveway, they will assess how much hardcore they need and arrange for that to be delivered to the site. They will then spread the hardcore across the sub-base to create a level surface to pour the concrete on. Most good contractors will apply a gel to any walls and doors to protect them from concrete splashes. They will also add any gulley tops, manhole covers or shuttering that’s required.
2. Installation and imprintingNext, the tradespeople will have the concrete either poured from a large mixer vehicle or barrow it in from a mixer and pour onto the surface. They level it with rakes, then add a colour surface hardener in a colour of your choice. This will give the driveway its permanent colour. They will then wait until the concrete has hardened to the correct consistency for imprinting the pattern, then will use special tools and stencils to make the pattern that you asked for. They will then spread a colour powder called a release agent over the surface, and leave to dry for 1 to 2 days depending on the weather conditions.
3. CleaningWhen the contractors return, they will add crack control cuts into the concrete. This is important because concrete expands and contracts in the heat, so there needs to be some give to stop any larger cracks from forming. Then everything is power washed clean, and a chemical wash is also used on the concrete to ensure it’s completely dust-free. The installers will ensure all your walls and doors are clean, which will hopefully be an easy job if they used wall gel.
4. SealingThe final step is to seal the driveway. There needs to have been at least two dry days before the tradespeople can do it, so you might find it’s best to have your pattern imprinted driveway installed in the summer. The contractors will blow any debris away from the surface and dry any damp areas where necessary. They will then add an anti-slip agent to the sealant and brush it on. It’s best to not walk or drive onto your new concrete driveway for about 4 days after sealing to allow everything to set. But after that, you’re ready to use your new driveway!

No, pattern imprinted concrete shouldn’t be slippery. Most good driveway installers will add a special anti-slip agent to the sealant before they brush it onto your driveway, so it will stop it from being slippery.

It’s important to ask a driveway company how they will seal your driveway when you get a quote from them. If an untrustworthy company seals your driveway badly, it can cause a thick and extremely slippery surface, so it’s vital that you ask any contractor what their procedure is before you engage them.

It’s also important to remember that pattern imprinted concrete isn’t a ‘non-slip’ surface – it’s just not slippery. You could still slip over on a concrete driveway, just like you could on tarmac or a block paved driveway. Also, once you’ve walked and driven over your driveway for a few months, its skid and slip resistance will increase as it weathers and builds up tiny specs of dirt on it. Pattern imprinted concrete is often used in high footfall areas in places like shops, fast food restaurants and theme parks, so if there was a significant slip risk these businesses wouldn’t use it.

You might think that you could ask your contractor not to seal the driveway to make it less slippery, but it could actually do the opposite. By sealing pattern imprinted concrete, it means that moss and algae is much less likely to grow, which can be extremely slippery to walk on if it’s left to its own devices. If moss does form on your driveway, the sealed surface is much easier to clean as you can simply pressure wash it away; this is not as easy to do on a non-sealed surface.