Driveway Repair in Mayfield

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.

Pitting, also referred to as spalling is the event whereby “pits” or small holes start showing on the surface of your concrete driveway which makes it appear both worn and uneven. Concrete driveway pitting is a common but highly frustrating problem for most homeowners. You’ll see some concrete driveways that’ll only start to pit after a couple of years, but this is not true for all concrete driveways as others will start to show signs only after a couple of months. So how do you tackle this issue? Well, it’s relatively simple to tackle, however if you’re not confident or lack the necessary skills, we’d recommend you get in touch with a reliable professional who can guarantee the best results for help. In this guide, we’ll take you through the concrete driveway pitting repair process.

✓ Prepare the pits by cleaning the area, clearing out all debris and more. The small pits can be cleaned with a stiff brush while a sturdy broom will do a good job for larger pits.

✓ Make use of a hose to spray the concrete pits and flush out all remaining bits of waste.

✓ If you’re tackling series of small pits, simply use a caulking gun filled with pre-mixed epoxy and specially formulated for concrete to fill the pits. Clear off the excess eproxy ensuring that its level with the concrete surface. Once done, simply leave for at least 24 hours before the application of a concrete sealant to prevent the wear and tear of the new concrete.

✓ Chisel out a little concrete and clean with a pressure washer. Once done, apply a concrete resurfacing compound mixture into the holes and use a trowel to level off.

✓ Ensure that the repaired concrete driveway is protected from rain and foot traffic for at least 6 hours (or 24 hours for vehicles).

Is there a hole in your asphalt driveway you feel you can repair yourself? If it’s something you know you can confidently do then this step by step guide is just for you. If otherwise, then we’d recommend you hire the services of a reliable professional who can guarantee the best results while also saving you some time and extra money that could result from possible errors. In this article, we’d go over the reparation process of an asphalt driveway with a hole in it.

✓ Get the necessary tools. You’re going to need a broom ( to clean the area), caulking gun ( to fill the hole), a hand tamp a plate compactor or a hammer ( to level the filled in hole) and a weeding glove (just in case there are weeds growing in the hole).

✓ Prepare the area. Do this by weeding the plants or weeds that might have grown inside the hole and identify your asphalt filler.

✓ Wet your soil, if necessary. It’s important to note that this is only necessary if your soil is dry to help the filler stick properly.

✓ Fill in deep holes. If the hole goes down about 3 to 4 inches or more, simply fill it with any material like rocks, clay etc.

✓ Apply the asphalt filler. Fill the hole with the asphalt filler to about half an inch higher than the surface of the driveway.

✓ Level the filler. For a large hole, make use of a plate compactor or a hand stamp, but a hammer will be sufficient for smaller holes.

✓ Cover the hole, if necessary. If your home isn’t level, covering your hole with a piece of plywood is advisable.

✓ Clean off the seal. After the asphalt looks done and in place, simply brush away the debris from the seal to finish off the project.