Bathroom Design & Install in Burford

In general, a new bathroom will take 1-2 weeks to install. This will vary depending on the size of the bathroom and the range of new units. Tiling and installing underfloor heating will make this time significantly longer. Also factor in redecoration, flooring and potentional ventilation.

Tiling your bathroom will not only increase the visual appeal of your space, but also provide an additional layer which helps protect against potential moisture damage, moist growth and also makes the bathroom a lot easier to clean up. So if you’re are looking to tile your bathroom, it’s recommended to get in touch with a skilled professional to ensure you get the best results. However, this guide will provide you with a good insight on how to get through the process smoothly and avoid costly errors. Let’s take a look!

1. Get The Appropriate Substrate
2. Clean the surface on which the tiles will be placed
3. Make use of levelling spacers to ensure the tiles are even.
4. Get a cement-made backer board to install the tiles
5. You may require a large format wall adhesive for the installation, if the tiles are different
6. Set The Layout
7. You may need a dry layout for the tiles installation (installation without mortar or other bonding agents).
8. Start with the first wall opposite the bathroom’s entrance
9. Once completed, you can continue with the remaining parts of the bathroom wall.
10. Place the first tile at the centre.
11. Place the subsequent tiles on each side of the previous ones to have a more balanced installation.

There are three varying materials that can be utilized in installing wall tiles. These includes thin set mortar, epoxy and mastic. However, you should always make use of epoxy for large format tile layout. To do this, simply place the tiles at your desired angle and gently twist them to hold firmly in place. Continue with this process till you have successfully covered the entire bathroom wall with the tiles. Once done, leave the bathroom wall to dry.

It is advised that you hire the professional services of a tile installation company in order to get the best outcome especially if you lack the necessary experience, tools and knowledge to carry out the project. This will save you some time, effort and money.

Are you thinking about updating your bathroom? If yes, then you’d probably want to know how to go about it. Well, when it comes to bathroom remodelling, the process always begins with the drawing of a floor plan. If you don’t know how to go about that, then you’ve come to the right place! In this guide, we’re going to take you through the bathroom floor plan drawing process. Let’s take a look!

First and foremost, you can make use of the pencil and paper approach as it happens to be much cheaper than the computer based approach. Plus, you don’t have to be an art genius in school to complete the task satisfactorily.

1. Sketch it out. Create a rough sketch of the space on unlined paper. This should feature all openings like the doors and windows, the spots where the existing plumbing fixtures are located, the location of the electrical lines including outlets, receptacles, heating and cooling pipes and more
2. Add dimensions to the sketch. The next line of action would be to take measurements of the bathroom. With the help of a friend, hold the tape tightly at both ends in order to get the right dimensions. Then, measure the length of the walls, fixtures, windows and mark then roughly on the sketch. Once done, you can go back to double check the recorded measurements for accuracy.
3. Transfer the room dimensions to a sheet of graph paper. At the stage in the process, you should be aware that each 1/4 inch square on the graph paper is equal to 6 inches or half foot. You can start by drawing the bathroom walls and partitions as well as the surrounding areas. Then, add the doors and the direction they swing open and the windows present. Once done, draw the fixtures to complete the floor plan.

It is crucial to make the walls of your bathroom waterproof, and bathroom wall panels or bathroom cladding is not only a great way to do that, but its also the easiest way to update the look of your bathroom. When it comes to adding wall panels to your bathroom, there are a large selection of designs to choose from which means you’ll always find something that’ll suit your space. So how do you have them installed? With this brief guide, you’ll learn everything you need to know about the bathroom panels installation. Let’s have a look!

1. Get the right tools and supplies. You’ll require a handsaw, jigsaw, or circular saw, hacksaw, drill, hammer, 1200mm spirit level, sealant gun, suction cups and tape measure.
2. Prepare the bathroom. Ensure that the bathroom walls are degreased, clean and, dust and dirt free. Also make sure that its flat and even with a spirit level.
3. Make sure a fixing method is in place. If not, make use of treated battens as a fixing method. Fit all battens in such a way that’s plumb and parallel.
4. Fit the shower tray. Take a measurement of the shower tray to identify the length of the seal strips that is needed while also making room for the shower screen.
5. Add the seal strips.
6. Cut the panels to size. Mark the bathroom wall panels and cut to get the right measurement in both height and width. Also ensure to make room for pipe and shower head holes at this point.
7. Install the panels.