Bathroom Fitting in Galashiels

Once you have your new bathroom installed, or perhaps you’re only replacing the old downlights, you’d probably want to know how to go about fitting your new bathroom downlights. If yes, then you’re not alone! This is a very common question amongst several homeowners and we wish to guide you through once and for all. However, it must be said that if you are not a competent DIYer or probably lack the confidence or skills to pull this off, then it’s advisable to hire a professional to get the best results and also save yourself some money and time.

Here are the list of the tools you’ll need to fit your bathroom downlights: Tape measure, chalk line or laser, pencil, pad saw, hand drill, hole saw and screw drivers.

✓ Measure the bathroom ceiling and mark out the central point of the light which will be where the downlights will be placed. Drill a small pilot hole here.

✓ Check above the ceiling to ensure that there’s no pipes, joists or wires in the way. It’s always a good practice to make sure that there’s sufficient room around where the downlight is to be installed in order to avoid placing it too close to a joist or any other obstacle. You should try as much as possible to maintain a 6 inch gap around the spot where the downlight is placed to make sure the fitting does not overheat.

✓ Use a hole saw or a plasterboard saw to make the cut out for the downlight. Check the downlight’s box for instruction on the size.

✓ Once you’ve been able to make a clean cut ceiling hole, pull through the wiring through the hole so that the downlight can be wired. Once done, then you can fit the downlight into the hole by holding the two springs back against the sides of the downlighter and push up into the hole.

Home renovations are an incredible way not only to beautify and add value to your home, but also to breathe fresh life as well as energy into your living space. If you’re currently wondering what room to renovate within your home, you may want to consider the bathroom. Not only is this a room that’s subjected to everyday use, but also has to deal with water attacks on a regular basis.

It’s a place where you groom, relax, cleanse and shower, meaning a lot of time is usually spent in this relatively small room. So if you’re planning to renovate your bathroom, one of the most frequently asked questions is, “how much it’ll cost to fit a new bathroom?. Of course like many other home improvement efforts, the cost of fitting a bathroom is largely dependent on the materials to be used as well as the size of the bathroom, whereas the cost of installation may be a lot less than you would’ve guessed. In this simple guide, you’ll get all what you need to understand the average cost of fitting a bathroom and to develop a good estimate for your project as well.

Generally, professional bathroom fitter will charge varying amounts based on the material that’s to be fitted. For instance, small projects that only involves installing a new basin can cost within a range of £70 to £120, whereas larger projects which involves tiling a big bathroom cam cost within the range of £800 to £1,200. Overall, the average cost of fitting a new bathroom will range between £4,200 to £4,800. you can, however, save some money by shopping smart as well as comparing the prices.

Are you thinking about installing a new bathroom in your home? One thing that commonly crosses most homeowner’s mind is whether a task can be done by themselves without having to call on a professional for help and in turn, save them some money. So if you’re also thinking along this route, then you’re not alone!

Asides the kitchen, no other home project is probably more involved when talking about the systems as well as skills required. At times, it can be so complicated most expert DIYers will take a deep breathe before carrying out a remodelling job for a bathroom. Basically, bathroom installation will include electrical works, plumbing works as well as tile works which all requires a highly skilled tradesman. It’s the type of work where every square foot counts as it’s a dense, tight work. Apart from that, there are usually some frequent surprises here and there such as identifying rotting joists as well as sub floor underneath a leaking shower or terribly rusted cast iron plumbing stacks. And to round it all up, you’ll also have to deal with the time pressure that comes with a bathroom remodelling project as the room is a highly essential space within the home. As a DIYer you’ll be under immense pressure to get it all over with as soon as possible for continued usage.

The solution to all the problems is simply to call in a professional who can help you manage the project from start to finish. The advantage of this is that you’ll get a good job done and probably in a quicker time than you would have. However, the main reason why most homeowners might not want to hire a pro to handle their bathroom remodelling job is because of money. Ultimately, if you feel confident enough you can go ahead and do the task yourself. If not, then calling in a reliable professional would be your best bet.

Is your bathroom sink damaged or old and looking fragile? If yes, then you’re most likely interested in fitting a new one as soon as possible. So how do you go about the installation of a new bathroom sink? This is one of the most frequently asked questions when it comes to bathroom sinks and for a good reason. The fact is, if you’re DIY competent, then this is a task that shouldn’t give you too many hard times. However, if you’re without a proper training or experience, we’d recommend hiring the services of a plumber to guarantee the best results as save yourself some time and additional money which may result from costly errors. In this guide, you’ll learn the steps to bathroom sink installation.

✓ Tap preparation. Apply a small amount of plumber’s mate putty to the base of the taps to be installed.

✓ Install the taps. Identify the taps holes in the sink and squeeze the taps firmly in place, fit the washers and back nuts to the sink’s underside.

✓ Wipe off excess putty. Use a suitable tool to wipe off excess putty that has been pressed out by the tap.

✓ Install the wastage drain. Fit the wastage drain easily into the sink in such a way that the back and front (not side to side) is faced by the two wastage holes.

✓ Tighten the wastage pipe. Squeeze the wastage pipe in, include the washer on the opposite side as well as the nut. Tighten properly with an adjustable spanner and wipe off excess put using a screwdriver or any suitable tool.

✓ Fit the sink to the wall. Put the bolts in position before hanging the sink. Once done, then bolt the sink to the wall and tighten the nut with an adjustable spanner.

✓ Ensure that it’s level with the help of a spirit level.